modelmaker51 wrote: My solution is more permanent, take a dremel with a cutoff disc and grind each rail head to thin it from the inside by about half its thickness for a distance of about 3/8". Fill the groove created with epoxy and even it with the railhead when hardened. Be careful, you're only grinding enough away so that the wheel treads don't touch both rails as they pass through the frog. You don't need to go any deeper than about 1/16th of an inch.
My solution is more permanent, take a dremel with a cutoff disc and grind each rail head to thin it from the inside by about half its thickness for a distance of about 3/8". Fill the groove created with epoxy and even it with the railhead when hardened. Be careful, you're only grinding enough away so that the wheel treads don't touch both rails as they pass through the frog. You don't need to go any deeper than about 1/16th of an inch.
My method is much simpler. You don't have any gaps to fill or jumpers to solder. No flying pieces of rail either. You basically just grind out a little 3/8th in. long divot (about 1/16" deep) between the rails. Just check to see when the wheel tread no longer touches the other rail.
Selctor: What are you using for a cut-off disc? Is it one those big fibreglass re-enforced discs? They are indeed way to big. I'm talking about the quarter-sized 1.5mm thick cut-off discs and I think Joe is as well, they only make a about a 2mm gap.
Jay
C-415 Build: https://imageshack.com/a/tShC/1
Other builds: https://imageshack.com/my/albums
If you do the cuts, it will be quite a gap if you use a cut-off Dremel-type disk, at least if I'm doing the job. If you could spring for a jeweller's file, you would hardly see the gaps, and they would work like a darn. The problem with making the gaps, though, is that it now isolates both rail sections leading to the frog point. Smaller steamers with few pickups will possibly stall when their separated pickups don't span to the live parts. So, you must solder tiny jumpers from the opposite side outer rails to those small isolated ones to keep them powered, or hook up directly to the closest correct feeders.
Means drilling holes and doing some tiny soldering, but...so what?
Joe Fugate Modeling the 1980s SP Siskiyou Line in southern Oregon
I tried the nail polish and it seems to have worked like a charm. Thanks Selector and other who suggested it. I know it's a temporary fix but at least I now know that was definitely the problem. I learn something new everyday around here.
Joe, I do have a question on your suggested remedy. I understand where to make the cut and to use the superglue on the inside as shown below..
but, I don't quite understand the 'jumpers' you have in your picture. Do I need them if the track on the other side of the turnout is 'live'.. i.e. part of the mainline? I just need them for the passenger siding which this turnout services, right?
Thanks!
JaRRell
jfugate wrote: jacon12 wrote:I'll probably end up doing this as Joe says, but for the meantime I'll try the clear nail polish and see if that works. Just so I understand, is the area of track in red the place I do the painting? (Please disregard the larger red arrow). Yes, but you only need to go out to between the two ties in the red area shown -- just to the right of your clear polish arrowhead (about half as long as what you show). You don't want the insulated section to be any longer than necessary or then you will get the reverse problem ... things will stall on the frog instead of short.
jacon12 wrote:I'll probably end up doing this as Joe says, but for the meantime I'll try the clear nail polish and see if that works. Just so I understand, is the area of track in red the place I do the painting? (Please disregard the larger red arrow).
Yes, but you only need to go out to between the two ties in the red area shown -- just to the right of your clear polish arrowhead (about half as long as what you show). You don't want the insulated section to be any longer than necessary or then you will get the reverse problem ... things will stall on the frog instead of short.
Ok, I got it.... half as far.
Thanks Joe,
Sure, but I was talking about before, when everyone assumed it was an electrofrog. Insulated joiners would work there, right?
Thanks, Joe.
I'll probably end up doing this as Joe says, but for the meantime I'll try the clear nail polish and see if that works. Just so I understand, is the area of track in red the place I do the painting? (Please disregard the larger red arrow).
Thanks,
GearDrivenSteam wrote:Joe, wouldn't putting insulating joiners on the frog rails do the same thing?
Yes, I forgot to mention that it's an Insulfrog turnout. I appreciate everyones suggestions on a rememdy and Joe, the picture (diagram) is worth a thousand words. I've been wondering just where the wheels touch and now I know. I'll give the nail polish trick a try to see if that helps, I have a feeling it will.
Let's see..... where does she keep that stuff....
Thanks guys!
P.S. OH!!! How often does this happen? Rare... now and then.. almost never?
The problem is that both rails after the frog are energized and the wheels are touching both rails as they pass over the frog.
The solution I have seen here is to paint some clear nail polish on the rails from the plastic point of the frog on, (paint about 3/8" to 1/2"). This will have to be repeated from time to time as the coating wears away.
JaRRel, it is an easy fix. Get some clear lacquer, whether nail polish or varathane, and dab some on the rails where the frog points come together, but at the "fat" end, where the plastic and rails meet. In the photo directly above my post, in the red circle, add, and let dry, two layers of this "insulation" to the point where the way-too-wide HO scale wheels can't actually make contact with both rails at the same time...which is the problem. I have had perfect succes with the paint job, and you won't be able to tell it is there...until is wears off and you will know what to do.
I can tell yer havin' fun.
That Peco turnout is probably a live frog. Unless you have insulating rail joiners, my guess on what's happening is that the loco wheels are bridging the gap between the two rails I have pictured below. If that happens, then it's short city. Peco recomends insulating the frog rails anyway. Have a look and see what you think.
Insulating rail joiners might be all you need.
I had one engine where the screw holding the tender coupler was long and touched the frog, shorting it out. I had another where the flanges rubbed. Neither of these sound right for you in that all your engines cause the problem. Some time with a multimeter may show a short that has developed within the turnout itself. I am assuming this turnout is not part of a reversing loop, or a DC block where wires could have shorted or been misplaced.
Replacing the turnout could be the short way to find the short. Good luck.
I have a particular turnout, a Peco large radiius... that's giving me problems and I kinda new at working with them so I come to you guys. The problem is it has suddenly started to short when just about any of my locos crosses it. Most of the traffic on my layout crosses this turnout from right to left when looking at the photos below.
At first I thought the problem was at the points, that the loco's wheels were picking them..
but after watching as close as I can it looks more like the problem is in the area noted by the red arrow below (frog?)..
Short of pulling the turnout off the layout, what can I do to correct this problem.