Found it. Or at least found ONE of the articles on this conversion of the Atlas turntable
February 2002 issue of MR, "build an inexpensive turntable" by Bob Foltz, page 94. But again I think this was one of a few articles on that same general idea, in addition to the tutorial on this Forum that someone found
Dave Nelson
wjstixIn my experience, the Atlas TT is noisy if you use it powered with 12V. If you use only 3-4 volts, it's very quiet.
I wish I had thought of trying that! I thought I could live with the noise but the racket it made caused the hair on my neck to stand up. I couldn't tolerate it.
Lowering the input voltage is something to keep in mind for future motorized projects.
Dave
I'm just a dude with a bad back having a lot of fun with model trains, and finally building a layout!
I believe that one of the articles you are looking for is the "San Juan Central" project by Malcolm Furlow but it was a long time ago, possibly late 1980's? I don't have access to all my back issues. He essentially made it into a HOn3 Gallows turntable as I recall overlaying the 9" HO deck.
I had one of the old versions, wishing that Atlas made it a 12" or so version as I found it suitable for diesels but not for my 2-8-0 at the time!
Cheers from Australia
Trevor
[Doh!] *Slapping palm to forehead.* I was using the search box in the menu bar. It never occured to me that there were two search boxes.[/Doh!]
Dave--Nice looking turntable.
But I wanted to make the engineer dizzy.
I have a Bachmann EZ Track set transformer dedicated to the TT. Well, I'm also running the interior LEDs off the accessories side. At any rate, I think I was testing it at around 3V.
OvermodHe probably knows this already...
I want to thank everyone. I know what I have to do, I just don't know how I'm going to do it.
I don't have a 45 record adapter.
Chip
Building the Rock Ridge Railroad with the slowest construction crew west of the Pecos.
OvermodNow that the little gray box to the right of the page now works again, all he has to do is type his search terms in and click the hokey little detective's magnifying glass at the right.
I know, that's what I'm trying to tell him to do. He didn't seam to have any luck, so I linked it, direct.
The link I posted for him is what you will find when you type "Atlas turntable conversion" in the Search the Community box.
Mike.
My You Tube
The link with the regearing is for using a 'real' bridge on top, as is the link to the post from 11 years ago here with regrearing (if you can see past the annoying Photobucket watermarks). Also Mr. Beasley's thread just got revived - he did the same sort of thing, buried the Atlas table and connected it to a bridge with a proper pit. As did Dave.
--Randy
Modeling the Reading Railroad in the 1950's
Visit my web site at www.readingeastpenn.com for construction updates, DCC Info, and more.
rrinkerThen it devolves into a whole 'bonch' of machine tool stuff about Atlas lathes.
(IIRC, though, we might bear in mind that his concern isn't about indexing at all, but 'remoting' the mechanism under the layout and having a different pit construction up top. I'm not sure what combination of search terms would best find that correctly, either in Google or Community Search...)
If you at looking for the 10 degree mod, this is the first link that comes up when I type exactly (without hte quotes) "Atlas 10 degree index" in Google is this:
http://kathyicingonthecake.com/gratkestuff/Atlas10/
Second oine is similar but slightly different URL that links the same article.
Fourth one is the one from the forums here:
http://cs.trains.com/mrr/f/11/t/157709.aspx
Then it devolves into a whole bonch of machine tool stuff about Atlas lathes.
Something to consider, but I will need a longer turntable than the Atlas, and longer than 90'. However, I don't need fancy indexing, or even simple geneva gear indexing, as my turntable will be near the edge of the layout so I can align by eye.
In my experience, the Atlas TT is noisy if you use it powered with 12V. If you use only 3-4 volts, it's very quiet.
I guess the Geneva motion (stopping at each track) does make it slower than other turntables, I've never been in a big hurry to turn an engine so never really thought about it taking too long.
I forget the maker, but 10-15 years ago there was a company that made a cast turntable pit wall that was 63 scale feet in diameter in HO - which would work out to 9" diameter, matching up with the Atlas 9" TT. Unfortunately, by the time I realized that it would make convering an Atlas TT, it was no longer in the Walthers catalogue and I haven't been able to find it again.
mbinsewi SpaceMouse I'm missing something. Where did you type in the search parameters?
SpaceMouse I'm missing something. Where did you type in the search parameters?
SpaceMouseI'm missing something. Where did you type in the search parameters?
In the "Search the Community" box.
Hi Chip,
I finally found a photo of my Atlas turntable with the pit added. I used Plastruct brick sheets and an Atlas bridge IIRC. In my case I made the bridge longer by about 3", but shortening it would be easy too.
MileHere's a link to the new version of the Atlas drive: https://www.modeltrainstuff.com/atlas-ho-304-turntable-motor-drive-unit/
Thanks. I already have that unit,
SimonI like that project Chip. If I had the space, I would make one! Here is one thread: http://cs.trains.com/mrr/f/88/t/99558.aspx
That's to everyone who refered me to Mr. B's wonderful photo essay. And thanks to Kevin for bringing it forward.
Mike SpaceMouse When I did a search for Atlas Turntable Conversion all I got were ads. Can you post the link? http://cs.trains.com/search/default.aspx?q=atlas+turntable+conversion Mike
SpaceMouse When I did a search for Atlas Turntable Conversion all I got were ads. Can you post the link?
http://cs.trains.com/search/default.aspx?q=atlas+turntable+conversion
Mike
I'm missing something. Where did you type in the search parameters?
trainnut1250http://cs.trains.com/mrr/f/88/t/99558.aspx?PageIndex=1
I have figured out how to make links clickable!
http://cs.trains.com/mrr/f/88/t/99558.aspx
Now I just need to learn how to give them text names instead of web addresses.
-Kevin
Living the dream.
Chip,
I think you are referring to this thread:
http://cs.trains.com/mrr/f/88/t/99558.aspx?PageIndex=1
Guy
see stuff at: the Willoughby Line Site
dknelsonI also recall an outfit, was it Airfix? Or Heljan? that had a unpowered turntable that was larger than Atlas, unpowered, very simple, just the ring and the bridge, and really really cheap. Just a few bucks.
I had a Heljan (Con-Cor) cheapo on my N scale layout. I never motorized it. I had to reach in and rotate the bridge by hand. It worked fine that way. I had the motorizing kit for it, but that was a joke.
Lakeshore SubI believe the article by Bob Hayden was about converting an Atlas plate bridge into a narrow gauge turntable using using a 1/4" phono plug which solved the issue of needing a split ring and gave it a center pivot.
Scott, thank you for the correction. I was obviously confusing the two articles with each other.
Kevin,
I believe the article by Bob Hayden was about converting an Atlas plate bridge into a narrow gauge turntable using using a 1/4" phono plug which solved the issue of needing a split ring and gave it a center pivot.
I made a small turntable using that article. Build the pit any way that you want and put the female end of the plug in the center of the pit. Epoxied the plug to the bottom of the bridge after flattening the leads from the plug against the bottom of the bridge also. Made some small holes in the bottom of the bridge to pass the wires from the leads to solder to the rails.Reversing the polarity is done with a DPDT switch regardless of using DC or DCC.
This is a really inexpensive way to get a small turntable in place.
No sure who did the article on placing the bridge on the Atlas disk itself.
Scott Sonntag
I remember more than one article, and perhaps thus in more than one magazine, about building up the Atlas turntable so that the base device would be sunk down and there was the traditional turntable "bridge" above, with the lower "pit" built on the old turntable platfom, so the pit would turn around with the bridge but in theory would hardly be noticed.
A friend of mine disabled his Atlas turntable's "Geneva" movement that creates those odd pauses, and wide spaces between index points, so that it is turned not by crank but by hand. Basically as with the idea of building a mocked up turntable on top of the Atlas, he is just using its precise centered support and its wiring which of course are two big challenges to scratchbuilding your own turntable.
I also recall an outfit, was it Airfix? Or Heljan? that had a unpowered turntable that was larger than Atlas, unpowered, very simple, just the ring and the bridge, and really really cheap. Just a few bucks.
As an idea for how to power a turntable years back I visited a layout in Illinois in an outbuilding, I think it was a layout that had been featured in Model Railroading or Rail Model Journal, lots of scratchbuilt locomotives, the owner was named Roger Miller but not the singer Roger Miller (although this Roger Miller did play the guitar) and the "power" for the turntable was a large plywood disc below the turntable, one edge of which stuck out a slot in the fascia. So the operator would just turn that disc by hand and eyeball the alignment of the turntable with the tracks above. It worked and struck me as a good idea and a workable way to disarm yet remotely power an Atlas turntable (it was the motor not just the drive that contributed to the noise, and it is the annoying "Geneva" movement's pauses that only add to the objections).
SpaceMouseWhen I did a search for Atlas Turntable Conversion all I got were ads. Can you post the link?
Try this:
Here's a link to the new version of the Atlas drive:
https://www.modeltrainstuff.com/atlas-ho-304-turntable-motor-drive-unit/
It promises a quiter drive. Since I assume the point of reference is the old noisy Atlas TT drive, I think this one should improve over those.
Mike Lehman
Urbana, IL
I cannot give you the issue date and year, but I only remember one article in Model Railroader about using the Atlas turntable.
In the artical, I think it was used as a Narrow Gauge tunrtable, HOn30 if I am remembering correctly, so it might have been by Dave Frary or Bob Hayden about their CARRABASSETT AND DEAD RIVER layout.
The author built a pit around the Atlas turntable and glued a bridge right to the deck of the model. I think it was a gallows style bridge.
The finished product looked really good. The author said the only problem was the pit floor turned with the bridge, but that was wasy to look past. He also suggested that if the pit was smoothed to look like cement that might make it less obvious.
I like that project Chip. If I had the space, I would make one! Here is one thread:
If you go in google and type this:
site:cs.trains.com/ atlas turntable conversion
You will find some.
Simon
DanI modified my Atlas (easy mod) to make the indexing with double the number of spaces, at half the distance apart, and you didn't have to sit and wait idle half the time for the mechanism to come around. I could 'splain how to do that if you're interested.
Dave in my humble opinion, the Atlas turntable is a ridiculously noisy piece of crap! It takes forever for it to get to the track that you want. I would choose any other turntable instead of the Atlas unit.
It's the one I have. I'm going to try to cover it with a layer of styrofoam.
MikeNow that the search function seems to work, I did a "Search the Community" thing, typed in Atlas turntable conversion, got all kinds of articles, including converting an Atlas TT into a pit type TT, and all kinds of ideas for a solid deck. I have't tried a search of the archives yet. Mike.
I have't tried a search of the archives yet.
When I did a search for Atlas Turntable Conversion all I got were ads. Can you post the link?
rrebell One used a cilander in the center glued to the atlas with a pit suported by the sides of the table so that it didn't touch the deck. Then they built the bridge. The thing about the Atlas turntable is it is super reliable and simple.
That was the approach I wanted to take. A stationary pit, not a moving deck.
Steve in Texas Search For "Atlas 10 Degree index" in Google. It is a mod using 2 gears attached to the center of the deck to get a reduction to 10 degree index.
Search For "Atlas 10 Degree index" in Google. It is a mod using 2 gears attached to the center of the deck to get a reduction to 10 degree index.
Thanks
Mike The newer drives for the Atlas TT are connected by a rubber o-ring or belt drive. These should be quieter than the old all-gear drives. Anyone know?
The newer drives for the Atlas TT are connected by a rubber o-ring or belt drive. These should be quieter than the old all-gear drives. Anyone know?
Don't know.
SimonYeah, get yourself a comfortable chair with a good beverage if you get an Atlas. And larger, reliable turntables are not cheap. On the other hand, I could see someone using an Atlas for only two stalls, which would make the waiting time acceptable. And there would be no issue with DCC polarity if you don't turn locos around. My Atlas was fairly quiet - I still have it, 40 years after using it on my first layout. Maybe I got lucky. Simon
Two stalls and a straight through RIP track. I'm not sure it will get much use. Mostly for looks.
hon30critter SpaceMouse Does anyone know what I'm talking about? Hi Chip, I modified an Atlas turntable to install a proper bridge quite a few years ago. It took a bit of effort to build a pit wall and a floor above the original turntable but it turned out okay. However, in my humble opinion, the Atlas turntable is a ridiculously noisy piece of crap! It takes forever for it to get to the track that you want. I would choose any other turntable instead of the Atlas unit. Dave
SpaceMouse Does anyone know what I'm talking about?
I modified an Atlas turntable to install a proper bridge quite a few years ago. It took a bit of effort to build a pit wall and a floor above the original turntable but it turned out okay. However, in my humble opinion, the Atlas turntable is a ridiculously noisy piece of crap! It takes forever for it to get to the track that you want. I would choose any other turntable instead of the Atlas unit.
Always wanted to get a 3-d printed replacrment gear for the one with the blank area on one side, would make the turntable not have aby predetermaned stops. As far as what the OP wanted, there are counlest articales and ways to do it. One used a cilander in the center glued to the atlas with a pit suported by the sides of the table so that it didn't touch the deck. Then they built the bridge. The thing about the Atlas turntable is it is super reliable and simple.