zugmann Like when you have cars for the MOW yard and they neglect to take their locks off the switches before they go home so you can give them the cars they ordered?
Like when you have cars for the MOW yard and they neglect to take their locks off the switches before they go home so you can give them the cars they ordered?
Or take the lock off and don't put a keeper back in the handle.
Customers do both of those things too.
To be fair, train crews have caused a number of derailments by forgetting to properly secure switches too.
MOW vs Transportation battles are almost as good as Conductor vs Engineer, or Management vs Customers........
Greetings from Alberta
-an Articulate Malcontent
mvlandswThat saved your finger from getting sore pushing on it.
Been there. One of our F units has a spring loaded lever that you have to hold over to keep sand on. Better than having to keep a button pushed...
Larry Resident Microferroequinologist (at least at my house) Everyone goes home; Safety begins with you My Opinion. Standard Disclaimers Apply. No Expiration Date Come ride the rails with me! There's one thing about humility - the moment you think you've got it, you've lost it...
Some of the newer engine have sand switches that time out (usually just when you need it most) even when moving.
The wooden fusee striker caps were just the right size the wedge into the some of the pushbutton sander switches. That saved your finger from getting sore pushing on it.
Mark Vinski
mudchickenAny roadmaster that has a good sized yard or engine facility wonders why so many folks don't know where the O-F-F switch is on the locomotive for the sanders.
Happened more than once. None of us are perfect.
Some engines, when you center the reverse, the "sand" light goes out, even though the sanders are still blowing.
It's been fun. But it isn't much fun anymore. Signing off for now.
The opinions expressed here represent my own and not those of my employer, any other railroad, company, or person.t fun any
tree68In steam days, I understand that some railroads had steam jets behind the drivers on passenger locomotives to blow the sand off the rails. The idea was to reduce rolling resistance.
.
mudchicken Murphy of Arabia (SD good enuf?): Any roadmaster that has a good sized yard or engine facility wonders why so many folks don't know where the O-F-F switch is on the locomotive for the sanders. Kinda hard buying into the idea that it's always a defective locomotive. That stuff (screened silica sand) fouls everything it gets into. The eco-friendly switch plate lubricant is like a magnet for sand. The red stuff is hard to set on and even harder to get off. (not like there is a really available steam hose around anymore).... Anyone seen a Kershaw yard cleaner around? {Deleted the photo so Internet Explorer users can read the paragraph that was covered by the photo} I miss good ol' Lubriplate graphite 'n grease , but fortunately I don't play roadmaster anymore.(laundress BossHen is grateful for that)... Like PDN's comment and the ones about cleaning out the flangeways full of engine crater and sand with the track forces, some things just happen in any era. Frozen waste sand in crossings and trackwork flangeways is a nightmare to chip out. The Alco sand fill "notches" were pretty obvious on their hood units and later switchers.
Murphy of Arabia (SD good enuf?):
Any roadmaster that has a good sized yard or engine facility wonders why so many folks don't know where the O-F-F switch is on the locomotive for the sanders. Kinda hard buying into the idea that it's always a defective locomotive. That stuff (screened silica sand) fouls everything it gets into. The eco-friendly switch plate lubricant is like a magnet for sand. The red stuff is hard to set on and even harder to get off. (not like there is a really available steam hose around anymore).... Anyone seen a Kershaw yard cleaner around?
{Deleted the photo so Internet Explorer users can read the paragraph that was covered by the photo}
I miss good ol' Lubriplate graphite 'n grease , but fortunately I don't play roadmaster anymore.(laundress BossHen is grateful for that)... Like PDN's comment and the ones about cleaning out the flangeways full of engine crater and sand with the track forces, some things just happen in any era.
Frozen waste sand in crossings and trackwork flangeways is a nightmare to chip out.
The Alco sand fill "notches" were pretty obvious on their hood units and later switchers.
Semper Vaporo
Pkgs.
NDGMany Fire Trucks wore chains all winter.
There are now available devices that swing into place when chains are needed. You can see the short chains hanging down next to the drive wheels on vehicles so equipped.
mvlandsw In the 1950's/60's some buses in Pittsburgh, Pa. had sanders in front of the rear dual wheels.
In the 1950's/60's some buses in Pittsburgh, Pa. had sanders in front of the rear dual wheels.
Thank You.
https://railpictures.net/photo/656980/
Note heavy white coating on lead truck, slightly less on rear truck.
Someone left the lead axle sand on......
The PA Turnpike used to cross the then double track B&O P&W Sub between Pittsburgh and New Castle - it crossed over the tracks on the Bakerstown Hill grade. When glancing down at the track structure it was easy to tell the normal up hill track from the down hill track (Current of Traffic signalling) - the Up hill track had a continuous white cast to it - down hill was just the norm black/brown track structure.
In the middle 70's, the P&W was single tracked by Chessie System. In the early 2000's leased the P&W to both the Allegheny Valley RR and the Buffalo & Pittsburgh. The AVL & BP perform all Dispatching and maintenance on the line.
Never too old to have a happy childhood!
Paul_D_North_Jr MOW people hate sand, for the reasons Murphy asked and zug answered - it fouls/ clogs the ballast in areas of heavy use (grades), and gums up the switch slide plates (and anything else similar, such as at a movable point frog) as well as filling the spaces around the operating and connecting rods, which means they need to be cleaned and lubed fairly often. I understand the C&S people also hate sand because of the deleterious effect it has on their gizmos, but since I don't belong to that tribe, I'll let someone else speak to that. Often there are general rules discouraging the use of sand in such places, but the need to keep a train moving on a heavy grade without slipping and stalling usually supersedes that. Also I understand that traction motors don't like it, but again will defer to someone else. Interesting article (mainly Euro-centric), including some of the downsides - especially interfering with good electrical contact for the signals: https://en.wikipedia.org/wiki/Sandbox_(locomotive) Interesting discussion here: https://www.federalregister.gov/documents/2007/03/06/E7-3885/locomotive-safety-standards-sanders Ad and price from one supplier - don't know anything more about it than what is shown: https://rrtools.com/product/traction-sand-20-40-coal-slag/ Would be interesting to see the technical specs for such sand. AAR has one, but I can't access it: "Specification M-916—Sand for Traction". Interesting discussion here on "locomotive sand": https://www.trainorders.com/discussion/read.php?1,2334762 Some here will appreciate and may want to comment on this quote from that TO thread (also has comments on SP sources): "Seems I remember that the Santa Fe in Sou Calif obtainedcompany sand from the Escondido District at Falda-Talicasiding...." Interesting comments here from 2011, including some by a couple of current participants: http://cs.trains.com/trn/f/111/t/196820.aspx - "Sand for traction" More ads for sand: https://www.olimag.com/en/traction/ http://www.wieserailservices.com/ - abotu halfway down, shows a price (Google is your friend) - PDN.
MOW people hate sand, for the reasons Murphy asked and zug answered - it fouls/ clogs the ballast in areas of heavy use (grades), and gums up the switch slide plates (and anything else similar, such as at a movable point frog) as well as filling the spaces around the operating and connecting rods, which means they need to be cleaned and lubed fairly often. I understand the C&S people also hate sand because of the deleterious effect it has on their gizmos, but since I don't belong to that tribe, I'll let someone else speak to that. Often there are general rules discouraging the use of sand in such places, but the need to keep a train moving on a heavy grade without slipping and stalling usually supersedes that. Also I understand that traction motors don't like it, but again will defer to someone else.
Interesting article (mainly Euro-centric), including some of the downsides - especially interfering with good electrical contact for the signals:
https://en.wikipedia.org/wiki/Sandbox_(locomotive)
Interesting discussion here:
https://www.federalregister.gov/documents/2007/03/06/E7-3885/locomotive-safety-standards-sanders
Ad and price from one supplier - don't know anything more about it than what is shown:
https://rrtools.com/product/traction-sand-20-40-coal-slag/
Would be interesting to see the technical specs for such sand. AAR has one, but I can't access it: "Specification M-916—Sand for Traction".
Interesting discussion here on "locomotive sand":
https://www.trainorders.com/discussion/read.php?1,2334762
Some here will appreciate and may want to comment on this quote from that TO thread (also has comments on SP sources):
"Seems I remember that the Santa Fe in Sou Calif obtainedcompany sand from the Escondido District at Falda-Talicasiding...."
Interesting comments here from 2011, including some by a couple of current participants:
http://cs.trains.com/trn/f/111/t/196820.aspx
More ads for sand:
https://www.olimag.com/en/traction/
http://www.wieserailservices.com/ - abotu halfway down, shows a price
(Google is your friend)
- PDN.
Why settle for plain old sand, when you can use genuine Trackmobile Trac-Grip!
https://trackmobile.com/project/trac-grip/
Most units have two sander switches, "manual sand" which will operate all the sanders in the consist, and "lead axle sand".
GE Dash-8's do not allow manual sanding above 7 mph. You can use lead axle sand at any speed on those, but it doesn't do a whole lot.
This may vary from railroad to railroad, but most if not all modern units have spring loaded sander control switches, so you cannot leave them on constantly (I tie my keychain lanyard from the manual sand switch to something else to hold it on, the rear headlight switch on our GEVO's is in just the right place!). For units with push button sanders, a bent up torpedo clip works pretty well to hold the button in, or the red flag from the flagging kit.
Older units like SD40-2's have a simple on/off switch that will stay in either position, so you can leave it on and then in theory forget about it and waste all the sand (not that anyone has ever done that, especially not when leaving units on the shop track).
I agree with Jeff that the computers on both GE and EMD units do not sand early or often enough.
Units from both builders have "sand anti-clog" features that periodically blow a shot of air through the sander valves and hoses, even if they are not in use.
As Zug said newer engines won't allow manual sand above certain speed ranges when in power throttle. They all will allow manual sanding in dynamic braking. All modern (at least the last 20 or so years) EMD engines are so equipped. I've noticed some of the newest GE engines also have this affliction. When above the speeds, and it varys between models but generally about 15mph, the computer can put down sand. I've noticed that usually it takes a lot of slipping before the computer decides it needs sand. On our worst hill, I hate to have an EMD lead when there is slick rain conditions with a close to full tonnage train. By the time the computer decides to lay sand it's usually too little, too late. You've lost speed too early on the hill to not stall.
As i said manual sand is always available in dynamics and I use it. Might even use it on that "flat as a pancake, treeless desert" that really doesn't exist (The flat as a pancake part) under the right conditions. I've noticed with sand you may not have to go as deeply into dynos as without it. The help sand gives may not be much, but sometimes it's enough.
One place sand is not supposed to be used is over the moveable parts of an interlocking or other controlled point. It's because sand is an insulator and enough could negate track detection of equipment or maybe when points have locked up. Either way, it's fun to shut off the manual sand coming up to such a place and then have the computer turn them back on through the restricted area.
Jeff
CShaveRRI can't find any figures for capacities of modern wide-nosed locomotives, but second-generation EMD locomotives could hold anywhere from 56 to 75 cubic feet of sand. Switchers held a lot less, sometimes as little as 17 cubic feet.
https://www.thedieselshop.us/DataAC4400.HTML
I can't find any figures for capacities of modern wide-nosed locomotives, but second-generation EMD locomotives could hold anywhere from 56 to 75 cubic feet of sand. Switchers held a lot less, sometimes as little as 17 cubic feet.
Carl
Railroader Emeritus (practiced railroading for 46 years--and in 2010 I finally got it right!)
CAACSCOCOM--I don't want to behave improperly, so I just won't behave at all. (SM)
Damp sand is a problem.
We once had someone get some play sand for use in the locomotives. It had small pebbles in it. Took ages to work all of that through and out of the system.
In steam days, I understand that some railroads had steam jets behind the drivers on passenger locomotives to blow the sand off the rails. The idea was to reduce rolling resistance.
PNWRMNM Murphy Siding Are there certain kinds of sand used for the purpose, like silica sand because it's so round and flows easily? Murphy, The best locomotive sand has lots of angular faces for better grip between rail and wheel and to avoid the higher loss from top of the rail associated with round grains. No beach sand! To the best of my knowledge, railroad sand is quarried. You might ask your local ballast train supplier if they recover their fines for sale as sand. IIRC they are mining quartzite which should make nice traction sand for both railroad and highway use. Mac McCulloch Mac
Murphy Siding Are there certain kinds of sand used for the purpose, like silica sand because it's so round and flows easily?
Are there certain kinds of sand used for the purpose, like silica sand because it's so round and flows easily?
Murphy,
The best locomotive sand has lots of angular faces for better grip between rail and wheel and to avoid the higher loss from top of the rail associated with round grains. No beach sand!
To the best of my knowledge, railroad sand is quarried. You might ask your local ballast train supplier if they recover their fines for sale as sand. IIRC they are mining quartzite which should make nice traction sand for both railroad and highway use.
Mac McCulloch
Mac
Thanks to Chris / CopCarSS for my avatar.
The prime consideration about use of sand on the railroad - IT MUST BE DRY.
The fuel service trucks that CSX normally contracts refueling with also top off the sand boxes on the locomotives they service, in addition to pumping the chemical toilets - at least they are supposed to, if they do in fact may be open to question.
http://cs.trains.com/trn/f/111/t/196820.aspx - "Sand for traction"
The streetcars of Toronto carry sand in hoppers under the frontmost seats. At some of the turn-around stations like Dundas West or Broadview, there are big plastic boxes full of sand on the platform and the driver fills the hopper with a shovel.
Hey, I've been thinking about sand lately, too. Murphy asked and Zug answered some of them. Thanks. A couple more:
1. Are there sand boxes in both ends of the locomotive? As I recall, diagrams I've seen only show one.
2. Steam engines had their sand boxes on top of the boiler where I think the heat would keep it dry. Is there any provision for keeping the sand dry with heat or anything else? Or is damp sand not a problem? I would think it would tend to clump up.
Murphy asked about sand on flat terrain. I remember years ago I was watching the wheels on the Genesis locomotives on City Of N.O. when it started moving in Hammond, La. (perfectly flat land), and it spit some sand out when it started. I assumed it was set up to automatically do this on every start. Of course I realize Amtrak procedures could very well be different from those on freight trains.
_____________
"A stranger's just a friend you ain't met yet." --- Dave Gardner
5. CSXT (and I presume many other railroads) has very strict specifications for the quality of traction sand that it purchases.
1. Both. Newer engines are more restrictive with when sand can be laid down. Older engines, you just flip the switch anytime. Also used when starting out a lot, and used for braking as well.
2. Both
3. Yeah, it can also mess up switches (gets in the grease)
4. Air
5. It's a fine sand, but I'm no sand expert. You don't want non-sand things in the sand - it will clog up the sanders.
6. Sure.
7. Don't know. Part of a daily inspectioni s to make sure the sanders are, in fact, laying down sand (used for emergency stopping). You can look in the sand hatches to see how much is in there, too.
I sure don't know much about the use of sand by locomotives. I know that sand is used to provide traction on rails, and I know the local BNSF yard has a sand tower. That's about it. So, some questions:1) Is sand used on hills, or on slippery tracks, or both?2) Is the sand automatically put down by a wheel slip sensor, or does the engineer turn the sander dispenser on and off?3) If sand is used a lot in a place, does the ballast in that place eventually fill up with sand and cause problems?4) Does the sand fall because of gravity or is is pushed out with air?5) Are there certain kinds of sand used for the purpose, like silica sand because it's so round and flows easily?6) Are there rail lines that never need sand, like flat as a pancake through a treeless desert, for example?7) How much sand does a locomotive carry? Who checks the level on the sand dipstick?8) How did I get this far in life knowing so little about locomotive wheel sanding?
Our community is FREE to join. To participate you must either login or register for an account.