BigDaddyDoes the motor mount pull out by pulling the motor upward or do I have to push up from the bottom of the chassis?
I just rocked back and forth and the motor pulled right out. I have heard some folks have the rubber nubs break off but that has never happened to me.
LL_motor-mount1 by Edmund, on Flickr
I had some new, still in shrink-wrap, Life-Like engines where the bearings were stuck solidly to the input shaft. The grease reacted with the bronze oilite bearings and formed a lacquer that was stronger than super glue! I used lacquer thinner to free these up.
Proto_gear-5 by Edmund, on Flickr
Proto_gear-3 by Edmund, on Flickr
BigDaddyI might need to put some kapton tape underneath.
You "shouldnt" have to put any Kapton on the motor bottom. There's plenty of space between the rubber mounts and the frame.
LL_motor-mount1a by Edmund, on Flickr
My photos are of the FA but the geeps are similar.
Regards, Ed
Put in new Walthers wheels and gears, set it on the test track (DC) and one gear tower buzzed, the other didn't move.
The big long brass screws under the fuel tank did not fall out, but the weight was easily removeable. There was lots of oil where the trucks meet the frame but the grease around the worm and bearing was brown.
I took off the gear covers and pulled the worms, cleaned them and the bearings. Both trucks turned easily without being attached. I attached the rear truck and it turned with the flywheel.
I attached the front truck and when I turn the flywheel, the bearings torqued out of the gear tower and those wheels didn't want to move. The bearings did not spin on the shaft. I had to worry them (like a dog worring a bone) and a little alcohol and now things move again.
Does the motor mount pull out by pulling the motor upward or do I have to push up from the bottom of the chassis? I might need to put some kapton tape underneath.
Henry
COB Potomac & Northern
Shenandoah Valley
I just take all that out on those versions and hardwire the decoder. The wires are all right there for you. If doing sound, that little 8 pin board that remains wastes a significant amount of space.
--Randy
Modeling the Reading Railroad in the 1950's
Visit my web site at www.readingeastpenn.com for construction updates, DCC Info, and more.
Big Daddy wrote: "I have only hard wired pre plug locos. I was expecting the decoder to plug into the circuit board, but the CB has male pins."
At least some of the Proto2000 (Lifelike) engines have a (for lack of a better term) "reverse 8-pin wiring harness" with female connectors, to which all the wires attach. This plugs down "over" the male pins on the light board, which is mounted to the weight with screws.
This is a Proto2000 GP30, but the connection scheme is the same:
You can see the small decoder that will replace the light board (at the bottom of the pic)
The wiring harness lifts off, and you can see the male pins on the light board:
Remove the light board and the decoder plugs into the harness:
And here it is with headlights before the shell goes back on:
That's a mess of circuit boards Ed. Yes, I was afraid if I just kept prying straight up, the bottom cover would crack.
I'm awaiting wheel gears. Will report back about whether it runs or not and stall current.
Those gearcase covers can be a bit fussy, Henry. I always fear I'm going to break one but, so far, never have. I use a very fine flat blade screw driver. You have to unsnap one then hold a little upward pressure on it while unseating the other clip. Takes a little dexterity
tstageI think only the Proto 2000 S1/S2s had the isolation issue, Henry.
I believe that's the case. I've never run into a GP, SD or FA series from Life-Like that had the motor brushes contacting the frame. I usually solder a new wire onto the bottom brush holder and, in a belt-and-suspenders kind of way, place a layer of Kapton tape over it to be sure. The motor sits in rubber mounts very similar to the Athearn method.
I scrap the lighting board.
DCC_PCBa by Edmund, on Flickr
The GP-20 board did have an odd setup where a bronze contact strip that engaged the top brush holder was part of the PC board :
DCC_PCB-gp20a by Edmund, on Flickr
Good Luck, Ed
Way back when, I looked over one of those boards that has the "cut here for DCC" marks. I traced out the circuit. Made no sense to me how they wired it, so I took the safe way out and removed the factory board and hard wired a decoder.
It's easy enough to check for isolation when you have it that far apart - the only side that could possibly be a problem is the bottom motor wire, so check continuity between there and the frame. If it's open, you're good to go. Pretty sure they are isolated.
tstage I think only the Proto 2000 S1/S2s had the isolation issue, Henry. You could always ohm it to double-check though... Tom
I think only the Proto 2000 S1/S2s had the isolation issue, Henry. You could always ohm it to double-check though...
Tom
As for those Proto 2000 S1/S2/S3 switchers, the motors were intended to be fully isolated from the frame, but the infamous 'orange wire' connected the lower brush to the frame. This in and of itself would not short the loco and fry the decoder, but a derailment could cause a short that would fry the decoder.
Don't ask me how I know.
Rich
Alton Junction
https://tstage9.wixsite.com/nyc-modeling
Time...It marches on...without ever turning around to see if anyone is even keeping in step.
rrinkerCracked gears don't usually jam all motion, and even if it did, the motor would hum or buzz when it jammed.
First of all, thanks Ed. The bottom plate wasn't coming off unless I exerted some lateral force where the tabs were. Thanks for the pic.
It has the 8 pin plug, circuit board dated 7/3/98. Pilot error on the test track, there was no power so there was no hum. The seller has good feedback so I think once the motor sees real DC, things will be OK.
Back to the conversion. I have only hard wired pre plug locos. I was expecting the decoder to plug into the circuit board, but the CB has male pins. Do I pull the circuit board and just plug it into the female plug? Looks like I do on the TCS site
Is the motor isolated from the frame on these later Proto models? Led's, yes I know, the only way to go
MisterBeasleyThere should be a thin plate on the flat bottom of the truck that comes off easily with a small screwdriver.
Proto_gear-4 by Edmund, on Flickr
MisterBeasleyIt's probably a good idea to put some LaBelle grease in before closing it up again.
Proto_gear-7 by Edmund, on Flickr
Yes!
There should be a thin plate on the flat bottom of the truck that comes off easily with a small screwdriver. The axles and gears just drop out and can be easily replaced.
It's probably a good idea to put some LaBelle grease in before closing it up again.
I have a couple of old DC engines like this. I hard wired in the decoders.
It takes an iron man to play with a toy iron horse.
If they are the pre-8 pin plug ones, there is a series where traces had to be cut for DCC. If they ever had DCC and those traces were cut, the motor will get no power from the rails. I'd test by using some jumer wires and touching right to the motor terminals.
Cracked gears don't usually jam all motion, and even if it did, the motor would hum or buzz when it jammed.
I've done this before, but I don't remember how. Hoseeker doesn't show the bottom plate on the truck.
Recently I've been messing around with Stewart locos and that piece has to be taken off by prying from above.
This is one with an 8 pin plug. My previous conversion was a pre DCC model so I'm going to have some questions about that too. But for now, when place on DC, nothing happens. It was advertised as non running bad gears, but a guy who seems to have a ton of them, all with the same problem.