Look up inter fire online and see what the fire marshals have to say about it also, very interesting statistics and they go into the problems of research in the area and how little research had been done (this was 2001 conference). Also look up the article Forensic Science on trial at the Science-Insider (never been there before but give great insite).
trainnut1250 rrebellDon't beleive me, look it up! The fires do strange things to wires like burning off insulation and causing shorts. Most fire departments, even large ones, do not investigate fires thoroughly unless loss of life occurs or arson is suspected. I did look it up. From the USFA site regarding fires in the united States in a years time.. "During a typical year, home electrical problems account for 67,800 fires, 485 deaths, and $868 million in property losses. Home electrical wiring causes twice as many fires as electrical appliances". more here: http://www.usfa.dhs.gov/citizens/all_citizens/home_fire_prev/electrical.shtm Seems these forensic experts have a different opinion. Guy
rrebellDon't beleive me, look it up! The fires do strange things to wires like burning off insulation and causing shorts. Most fire departments, even large ones, do not investigate fires thoroughly unless loss of life occurs or arson is suspected.
I did look it up. From the USFA site regarding fires in the united States in a years time..
"During a typical year, home electrical problems account for 67,800 fires, 485 deaths, and $868 million in property losses. Home electrical wiring causes twice as many fires as electrical appliances".
more here:
http://www.usfa.dhs.gov/citizens/all_citizens/home_fire_prev/electrical.shtm
Seems these forensic experts have a different opinion.
Guy
This discussion is interesting but is getting way off topic. The original question was, can DCC cause layout fires? No one has related a single instance of a layout fire caused by DCC.
jbinkley60 I think the key phrase here is "electrical problems." A house properly wired to the National Electric Code is highly unlikely to have a fire caused by the wiring, unless something serious breaks in the over current protection. If not, they had better toss out the code. If you doubt this, take a piece of 14ga wire and short out your nearby wall outlet and watch what happens. What they often find are houses that are not wired to code, things plugged into the house wiring or faulty appliances. I don't consider extension cord fires a house wiring problem. I had a relative that lost their house many years ago to the television set catching the living room curtains on fire.
I think the key phrase here is "electrical problems." A house properly wired to the National Electric Code is highly unlikely to have a fire caused by the wiring, unless something serious breaks in the over current protection. If not, they had better toss out the code. If you doubt this, take a piece of 14ga wire and short out your nearby wall outlet and watch what happens.
What they often find are houses that are not wired to code, things plugged into the house wiring or faulty appliances. I don't consider extension cord fires a house wiring problem. I had a relative that lost their house many years ago to the television set catching the living room curtains on fire.
I've had my share of things going PTOOF!! Things like plugging too many things into one extension cord. Or building amplifiers and then installing power cords to small for the amperage.
There is always something that can go wrong electrically. We had a fire in a house just behind us that was started by faulty outdoor lighting.
Any argument carried far enough will end up in Semantics--Hartz's law of rhetoric Emerald. Leemer and Southern The route of the Sceptre Express Barry
I just started my blog site...more stuff to come...
http://modeltrainswithmusic.blogspot.ca/
Engineer Jeff NS Nut Visit my layout at: http://www.thebinks.com/trains/
see stuff at: the Willoughby Line Site
rrebellSilver Pilot rrebell According to forensic scientist (the ones that try to start fires for a living) it is almost impossible to start an electrical fire (meaning a fire that can burn down a house). They said that local fire dept. blame electrical all the time but in most cases are wrong and are just trying to close a case. You get a lot of scare stories about foam also. I'll pass that along to my friends who had a house fired that destroyed their home. I'm sure it will be a comfort to them. The fire department said the cause was an electrical fire that started in the garage. Don't beleive me, look it up! The fires do strange things to wires like burning off insulation and causing shorts. Most fire departments, even large ones, do not investigate fires thoroughly unless loss of life occurs or arson is suspected.
Silver Pilot rrebell According to forensic scientist (the ones that try to start fires for a living) it is almost impossible to start an electrical fire (meaning a fire that can burn down a house). They said that local fire dept. blame electrical all the time but in most cases are wrong and are just trying to close a case. You get a lot of scare stories about foam also. I'll pass that along to my friends who had a house fired that destroyed their home. I'm sure it will be a comfort to them. The fire department said the cause was an electrical fire that started in the garage.
rrebell According to forensic scientist (the ones that try to start fires for a living) it is almost impossible to start an electrical fire (meaning a fire that can burn down a house). They said that local fire dept. blame electrical all the time but in most cases are wrong and are just trying to close a case. You get a lot of scare stories about foam also.
According to forensic scientist (the ones that try to start fires for a living) it is almost impossible to start an electrical fire (meaning a fire that can burn down a house). They said that local fire dept. blame electrical all the time but in most cases are wrong and are just trying to close a case. You get a lot of scare stories about foam also.
I'll pass that along to my friends who had a house fired that destroyed their home. I'm sure it will be a comfort to them. The fire department said the cause was an electrical fire that started in the garage.
Dr. Frankendiesel aka Scott Running BearSpace Mouse for president!15 year veteran fire fighterCollector of Apple //e'sRunning Bear EnterprisesHistory Channel Club life member.beatus homo qui invenit sapientiam
trainnut1250 The whole thing was over before I could react.
Jeff But it's a dry heat!
Not Impossible!!
I scratchbuilt a switch last year by soldering rails to circuit board ties. I didn't completely cut through the gaps in the ties in several spots. The short didn't draw enough amps to shut down the booster and the copper left uncut was just thin enough to burn like small little highway flares. I tested the switch on the bench late at night and was amazed to see several little fires pop up and burn as I applied power from my DCC system. The whole thing was over before I could react.
I don't consider this to mean a whole lot other than don't test stuff late at night and be careful to correctly gap your turnouts. But...It did technically catch fire.....I have attached a pic of the burnt switch if you need to see proof. Btw: I gapped the switch and installed it. Runs just fine and no I don't lose any sleep over the possibility of fire caused by DCC systems.
My layout is however one of the few that can can claim "Flame Broiled turnouts"
Thought you might enjoy the tale...
Impossible...I wouldn't dare say this,but I'd have to see one as it is so unlikely.Properly installed DCC components shouldn't be any concern but working in DC automotive (heavy machineries) electricity,I've seen a few "unlikely" situations happen so...it can't hurt to touch wires occasionally just to check if they aren't heating.Even with a well protected supply,light gauge wires,sloppy connections,etc can generate some heat without the circuit breakers detecting it.
A) I have never heard of a DCC system catching fire.
B) I have a 10 amp Digitrax Super Chief. I have had a short occur on the area farthest from the command station. It took me about 30 minutes to find it. It turned out to be in the truck of a passenger car. It just tripped the breaker every time I turned the power on. Nothing was damaged and nothing got hot. I have never fried a decoder or a switch machine.
While nothing is impossible, I consider your fire scenario to be so unlikely that worrying about it is pointless.
Dave
Lackawanna Route of the Phoebe Snow
retsignalmtrWhen I was working I had a coworker who enjoyed wrapping a piece of thin wire around a pencil to make a coil. He then put it between the + and - 12 volt power on a terminal board and when the coil lit up he would light a cigarrett with it.
When I was working I had a coworker who enjoyed wrapping a piece of thin wire around a pencil to make a coil. He then put it between the + and - 12 volt power on a terminal board and when the coil lit up he would light a cigarrett with it.
..... Bob
Beam me up, Scotty, there's no intelligent life down here. (Captain Kirk)
I reject your reality and substitute my own. (Adam Savage)
Resistance is not futile--it is voltage divided by current.
Other than smoked decoders or boosters the systems are pretty safe.
One thing that amazes me is that we haven't seen fires from people using alcohol in cleaning cars, especially powered ones. You have fresh alcohol on the tracks with potentially sparking engine wheels. Another is where people clean the tracks with alcohol while running trains. Same threat but worse if some spills.
Springfield PA
I've been a Digitrax DCC user/owner for over 10 years. I've smoked a few decoders (My Bad) but never woried about a fire. My DCC system is on a dedicated 20 AMP circuit protected by a circuit breaker; electrical outlet has an eletronics grade power stip with circuit breaker; DCC 5 AMP power supplies have circuit breakers; DCC command station (DCS100) and Booster (BD150) have circuit breakers; layout uses 12ga buss wire and divided into prower districts. Why all of this safety protection? Significant investment in eletronics, but not a worry about starting a fire.
Jim, Modeling the Kansas City Southern Lines in HO scale.
simon1966Our forum buddy Cudaken had the worst case scenario where his wiring caused the short protection in his MRC 8 amp booster to be defeated. It let the smoke out of numerous decoders, may have even caused the odd spot weld on a metal wheel, but his garage is still standing.
Our forum buddy Cudaken had the worst case scenario where his wiring caused the short protection in his MRC 8 amp booster to be defeated. It let the smoke out of numerous decoders, may have even caused the odd spot weld on a metal wheel, but his garage is still standing.
Not a big surprise
Hi!
Having been through a house fire at the age of 13, I can tell you the thought of another one scares the heck out of me. I am super cautious about anything that can instigate one, and have a house full of detectors and fire extinguishers. And yes, I've had fire training with two major oil companies as to causes, precautions, and actual fire fighting.
That being said, the previous posters were right on. Used as directed, DCC systems are as safe as plugging in your tv or other appliances. Trouble enters the picture when folks that "don't know what they are doing" make their own power supply or modify the innards of the systems, and the like.
Frankly, the real danger of a "layout fire" is stuff like the mis-use of a soldering iron, or open flame torch, or improper lighting. And, having electrical connections left turned on when you leave the layout room is also a potential contributor to disaster.
I strongly urge you to have a smoke detector or two mounted in your layout room, and to fix your layout wiring so that you can easily turn off ALL room power when you go.
Hey, please take care!!!!!
Mobilman44
ENJOY !
Living in southeast Texas, formerly modeling the "postwar" Santa Fe and Illinois Central
DCC causing a fire? Yes it could happen. I had a loco derail on a Peco switch when I left the room with the train running and when i returned many minutes later I didn't pay any attention to the stopped train. But I did smell melting plastic. When I looked around for it I noticed the derailed loco and the strong odor of the plastic. The loco had derailed and a wheel made contact with a rail of the opposite polarity and caused a short but the short was not drawing the amount of current to trip the boosters circuit breaker. The rail at the point of contact was glowing red and the plastic on the truck and the plastic ties and frog were melting. Had this condition not been removed, how much longer would it have been before the melted plastic would ignite? This was on a 5 amp super empire builder, N scale voltage setting. Ever have a coil on a switch machine burn out due to a stuck button? It is fortuate that the coil wire opens to stop the current flow. When I was working I had a coworker who enjoyed wrapping a piece of thin wire around a pencil to make a coil. He then put it between the + and - 12 volt power on a terminal board and when the coil lit up he would light a cigarrett with it.
Simon Modelling CB&Q and Wabash See my slowly evolving layout on my picturetrail site http://www.picturetrail.com/simontrains and our videos at http://www.youtube.com/user/MrCrispybake?feature=mhum
Oakhurst Railroad EngineerI've been researching the switch from DC to DCC for a month or so now. If I had a $1 for every person that said or typed that you have to be extremely careful because a DCC short is like a soldering iron that can catch your layout on fire ... I would have enough money to buy lunch at the big train show in Long Beach on Saturday.
Start a fire? I've not read that before. I have read that there is enough 'juice' to cause a shorted DCC system to act like a spot welder and have the potential to spot weld a shorted set of wheels to the rail if the short is not sense by the command station. That's the reason why heavier gauge wire should be used for the bus lines and why to perform the 'quarter test.' The quarter test is meant to see if the system is properly shutting down when a short occurs. As evidence to the potential look at the TTX report on autoreversers. The slower to react units with a mechanical relay show a spark between the rail and the wheels when the short occurs. Unresolved, the short, especially on an 8 amp or 10 amp system has the potential to do damage.
Marty
Melt wire, ties, maybe a little scenery but a fire? No. Maybe if you really try you could. Perhaps if you run a 20 foot buss through extruded foam and paper scenery with 28 Ga wire and put a 10 amp booster on it. I would imagine the end of the feeders would burn off first before a fire would start.
Maybe Mythbusters can try this out before they break out the C4.
Pete
I pray every day I break even, Cause I can really use the money!
I started with nothing and still have most of it left!
This is just a rumor started by someone with little or no knowledge of DCC. I say DCC, because it's obvious that the originator is trying to justify his/her own feelings against DCC. Fact is DC and AC can caue fires too. I used to teach Boy Scouts how to start a fire with a 9 volt battery and a piece of steel wool. Ever see what can happen if you drop one of those coin cell batteries in a pants pocket full of change?
The only "fire" I've ever seen at a train meet was a smoking Lionel Transformer. We had already unplugged it and moved it to the parking lot when the fire department arrived. There never was any actual flame.
Martin Myers
Now that´s a new one for me! I am A DCC user since the 1990´s and I have never heard of a layout fire being caused by a DCC system before. Yes, I have had a decoder melting down due to overload, caused by binding gears and a decoder, which was not designed for the amps the motor drew, but that´was all.
If this were a serious discussion, I could see our insurance rates going up!
selector I spell Bravo Sierra....over. (That's military radio comms speak for, "BS") Your decoder could go poof and emit its magic smoke, and if you have a power supply capable of melting the rails to a quarter when you do the quarter test, and if your shorts detection circuitry.....doesn't.... then, yes you may get some molten metal, but it would take a lot of juice for some time to achieve it. And that can happen in DC just as easily...since shorts are shorts are shorts. You never hear of this because the systems are both well engineered and well built with quality components that really do detect the shorts in milliseconds, at which they shut off power. You can't even blink that fast. -Crandell
I spell Bravo Sierra....over. (That's military radio comms speak for, "BS")
Your decoder could go poof and emit its magic smoke, and if you have a power supply capable of melting the rails to a quarter when you do the quarter test, and if your shorts detection circuitry.....doesn't.... then, yes you may get some molten metal, but it would take a lot of juice for some time to achieve it. And that can happen in DC just as easily...since shorts are shorts are shorts.
You never hear of this because the systems are both well engineered and well built with quality components that really do detect the shorts in milliseconds, at which they shut off power. You can't even blink that fast.
-Crandell
I wonder if this didn't originate with that same school board genius who was mentioned, and derided, on another thread.
Old Lionel transformers could put up to 75 watts on the rails at full throttle, and the voltage was higher. The same is true for present-day three rail AC systems. If they were even a potential fire hazard the Consumer Product Safety Commission would be all over them.
By way of contrast, a five amp DCC power station only puts 60 watts on the rails. If circuits are protected by the tried and true automotive bulb in series, this drops to 24 watts.
In sixty years of following the local news, I have never heard of a fire caused by a model railroad. When the cause of fire was electrical, it usually involved overloaded 120V circuits (somebody stuck a nickel in the socket and screwed the blown fuse back in) or frayed 120VAC cords arcing over in the presence of something a lot more flammable than the average layout.
I agree with Crandell. The whole base premise has the delicate aroma of bovine excrement.
Chuck (Modeling Central Japan in September, 1964 - with circuit breaker protected power supplies)
Marty,
DCC systems are generally designed with some sort of built-in short protection in the them. So, unless you are doing something intentionally harmful or unorthodox wire-wise and somehow bypassing the short protection, I don't see a fire ever being an issue.
As other have already stated, I've never heard of this ever happening to someone's layout.
Tom
https://tstage9.wixsite.com/nyc-modeling
Time...It marches on...without ever turning around to see if anyone is even keeping in step.