Haven't had a close read, only a look at this page, but it's good for another cup of coffee.
http://yourrailwaypictures.com/CNRsteamengines/
Brent
"All of the world's problems are the result of the difference between how we think and how the world works."
Good question, I searched a number of records of the CNR 2-10-2's and found this site.
Old Time Trains
Try searching, http://cs.trains.com/mrr/f/13/p/2785894/reply.aspx
It appears that the CNR were operated between Toronto and the Maritimes only.
CNR had a lot of 2-8-4 and 4-8-4 locomotives and many of them worked the western provinces. These would most likely be your Rocky Mountain haulers
http://www.trainweb.org/oldtimetrains/photos/cnr_steam2/santa_fe.htm
Not really an answer to this topic, but also not offtopic:
I heard a few times that CN used their T-2a 2-10-2´s (which had more traction force than CP´s Selkirks and were the strongest steamers in Canada by the way) also in passenger service in the Rocky Mountains in British Columbia. Was that regularily or occasionally?
There's a current item on the Classic Trains site under The Way it Was. The title is Green Beans and Trains. The author describes his experiences in Ohio, picking beans beside the Erie while an Erie K-4 4-6-2 worked the local freight.
Tom
M636C....A class G-5 built in the 1940s was a modernised G-2 intended for both freight and passenger on lighter track.....
I recently saw video of two G5s being transported from the Virginia Central to Winnipeg, Manitoba. I'm not sure of what's planned for them, but both appear to be in relatively good condition. There's apparently more info (for Trains subscribers only) to be found here:
former-canadian-pacific-4-6-2s-to-move-to-winnipeg-from-virginia
Wayne
Guy,
I have the complete set of Ian Wilson's books on CN steam in southern Ontario. There are many photos of Pacifics, especially the light ones, used on branchline freight in the '50s.
CN Charlie
CN subsidiary GTW in Michigan used J class light pacifics on branch line mixed trains, there are a lot of photos of 4-6-2 powered trains on the Caseville branch.
It should be remembered that most CN Pacifics had been built for predecessor roads and were not of a consistent design.
They fell into two groups, class J with 69" driving wheels and class K with 72" driving wheels. Those with 69" xdrivers would be considered as mixed traffic types...
check out:
http://www.trainweb.org/oldtimetrains/photos/cnr_steam2/pacific.htm
There are a number of photos with a box car behind the loco but these could be for express or be part of a mixed train. A complete mixed train is illustrated. Theb photos generally date from the 1930s to the 1950s.
The CPR built Pacifics in pairs with either 75" or 70" driving wheels...
The older lighter Pacifics were classes G-1 and G-2
The heavier type were classes G-3 and G-4.
A class G-5 built in the 1940s was a modernised G-2 intended for both freight and passenger on lighter track.
CPR also had two typres of Mikado, P-1 and P-2 that shared the boilers with the G-1 and G-3 respectively.
In particular, the smaller wheeled G-4s were based in British Columbia for passenger service on heavy grades.
M636C
"One difference between pessimists and optimists is that while pessimists are more often right, optimists have far more fun."
The RF&P was very unusual in that they never owned a 2-8-0 nor a 2-8-2. Freight was handled by 4-6-0's, 4-6-2's, 4-8-2's, and 4-8-4's. The 2-wheel lead trucks found on the road's WWII era 2-8-4's were an aberration. RF&P wanted more 4-8-4's, but the War Production Board had a different opinion.
On the NYC the K-11 Class Pacifics with 70" Drivers were almost exclusively used in Freight Service.
Also the ACL Pacifics were used in Fast Freight (read pershible fruit) service from Florida to the Northeast.
Rick J
Rule 1: This is my railroad.
Rule 2: I make the rules.
Rule 3: Illuminating discussion of prototype history, equipment and operating practices is always welcome, but in the event of visitor-perceived anacronisms, detail descrepancies or operating errors, consult RULE 1!
The Erie Railroad used Pacifics on branchlines for freight service on weekends when they were not needed for commuter service.
Especially late in the steam era, it wasn't unusual to see 'passenger' steam engines running out their last days on freight. On the flipside, IIRC the CN 2-8-2 at Steamtown was regularly used on passenger train locals running to - from Port Arthur / Ft. William Ontario (today's Thunder Bay).
It's very probable that the pacifics were used in freight. I'm not positive on the CN but I do know there is video of CP 2317 on freight duties toward the end of it's CP career before ending up at Steamtown. At the very least there are instances on most railroads of passenger engines being used in freight in either a shake down run after rebuild or just being power short. Engines also get replaced from higher profile jobs and demoted to branch service, frieght, or work trains (where ever useful) before retirement.
Flickr: https://www.flickr.com/photos/60361449@N02/
Anthracite Modeler - YouTube
I understand that, with their large drivers, the Pacifics (4-6-2) were primarily used for passenger trains. Did the CN also used them for hauling freight in the 50's?
I saw a photo of a Pacific used as a helper on a freight train but none as the primary mover.
Guy
Modeling CNR in the 50's