Yes
Yes L shape I had do this before because my foundation at my last house was old and not true.. I retook at the walls today I missed the baseboard they have at the bottom of the drywall.. so I may have additional marking for studs their already.. the other reason for the double wall as they say was in the event I move again I can put up wooden shelves which is plus for storage down here. I don't get water in other then by the garage main overhead door. It been pretty dry considering some of the storms we get in Arkansas..
PED Having water come onto the floor does not sound good even if you can keep all the electrical up high. You might consider a low dam across the doorways to at least keep the water out. You can build a concrete dam sorta like the speed bumps in the street so you can drive over it.
Having water come onto the floor does not sound good even if you can keep all the electrical up high. You might consider a low dam across the doorways to at least keep the water out. You can build a concrete dam sorta like the speed bumps in the street so you can drive over it.
I agree. Water on the floor means you will have humidity problems in the room which could tranlate into problems with the layout, like expansion/contraction problems that may play havoc with the track kinking etc.
Best thing if possible, is to control the envoronment as much as possible to limit the temp and humidity extremes.
Rio Grande. The Action Road - Focus 1977-1983
Paul D
N scale Washita and Santa Fe RailroadSouthern Oklahoma circa late 70's
Brian, it does sound like the OP knows where the studs are according to his information provided (I bolded below).
conrail0721I get to use two walls for the layout so it will be basically a l shaped shelf the walls r drywall already I don't trust the builder for making the studs 16 inches on center. So I planned to get some 2x2 ripped in half to be the new supporting studs held in place with lag screws and adhesive. Then build an open grid layout with the remaining ripped 2x2 for legs in key spots putting dry wall up for the back drop. This might be overkill but I know where the studs r and can drill out holes for power and keep off the floor to prevent water damage during the heavy rains we have here . Your thoughts?
so it will be basically a l shaped shelf
the walls r drywall already
I don't trust the builder for making the studs 16 inches on center. So I planned to get some 2x2 ripped in half to be the new supporting studs held in place with lag screws and adhesive. Then build an open grid layout with the remaining ripped 2x2 for legs in key spots putting dry wall up for the back drop. This might be overkill but I know where the studs r and can drill out holes for power and keep off the floor to prevent water damage during the heavy rains we have here . Your thoughts?
The layout is I shaped? or did you mean L shaped along two of the walls, which have drywall installed already.
My question is why do you need to rip 2x4's down to 2x2 for support for the shelf layout?
It sounds like you know where the studs are (stud finder) as you mentioned so you can mount shelf supports to the studs behind the drywall, which should be totally sufficient for supporting the shelf layout?
Yes, it seems like overkill and unnecessary to me.
Alternative you might consider,...
With a stud finder tool you might just locate the 2x4 studs already there behind your existing drywall. Then instead of making shelf support brackets for each stud, stretch a piece of angle iron horizontally across the wall attached to the studs ( I'm using a combination of sign-post square metal tubing and good strong bed-frame L-shaped framing I find at old surplius stores).
Then cantilever your plywood shelves out from these strong horizontal metal frameworks, with perhaps only an occassional vertical support member.
Brian
My Layout Plan
Interesting new Plan Consideration
Could you post a drawing? I don't quite understand what you mean.
.
It sounds like you are adding a wall over the wall.
-Kevin
Living the dream.
Don't know that I totally understand your posting.
Are you going to make 'additional studding' out of ripped 2x2 on 16" centers,...additional to what studs are already in the garage??
I have just become semi retired. Due to two strokes in 3 months. Likely no disabling effects other then some fine detail vision loss on my left side. So I have a two car garage with a single door, I get to use two walls for the layout so it will be basically a l shaped shelf the walls r drywall already, I don't trust the builder for making the studs 16 inches on center. So I planned to get some 2x2 ripped in half to be the new supporting studs held in place with lag screws and adhesive. Then build an open grid layout with the remaining ripped 2x2 for legs in key spots putting dry wall up for the back drop. This might be overkill but I know where the studs r and can drill out holes for power and keep off the floor to prevent water damage during the heavy rains we have here . Your thoughts?