Reading TrainsBuddy's post regarding back-up light placement on "B" units made me think of another question that I just took for granted. Apparently "B" units have a front and back end. Connected in an A-B configuration, are the engines oriented with both "front" ends facing in the same direction or are they connected "back to back?" What was general practice?
Chuck
Grand River & Monongah Railroad and subsidiary Monongah Railway
I can't speak to what other railroads did, but on the Santa Fe, initially, the units were kept as sets, and usually "front" to "back" with its consist. Later on, this changed as the units were separated and assigned as needed, and the pairings were random, depending solely on which way the B-units were facing at the time.
Robert Beaty
The Laughing Hippie
-----------------------------------------------------------------
The CF-7...a waste of a perfectly good F-unit!
Then it comes to be that the soothing light at the
end of your tunnel, Was just a freight train coming
your way. -Metallica, No Leaf Clover
I just wanted to be the first to say, it all depends on the RR. Usually you see them long hood to long hood, or long hood to short head, but this is also with non-booster locos that have cabs. It was generally thought as safer to put as much distance between cabs for safety reasons, like crashes. Which doesn't make sense because from what I under stand in MU consists, say one with 3 locos, only the first "lead" loco would have a crew in them, the other locos would be crew less. I personally will run MU trains with the most distance between cabs, in other words the first two engines long hood to long hood, and the middle and end cab would be long hood of end cab to short hood of middle cab. You have a really good question though, I will have to keep my eye on this post. A good example I just realized is the ad >>>> right over there for Standard Hobby Supply. Pair of BNSF (Dash 9's or AC4400's?) paired up long hood to long hood.
Thanks, Robert -
My railroad will have a number of A-B sets and I really never considered that B-units had a "front" and "back."
GRAMRR Apparently "B" units have a front and back end. Connected in an A-B configuration, are the engines oriented with both "front" ends facing in the same direction or are they connected "back to back?" What was general practice?
MILW-RODRA good example I just realized is the ad >>>> right over there for Standard Hobby Supply. Pair of BNSF (Dash 9's or AC4400's?) paired up long hood to long hood.
GRAMRRMy railroad will have a number of A-B sets and I really never considered that B-units had a "front" and "back."
Perhaps I should have mentioned this since your OP was about "B" units. If you are reffering to 2nd gen diesels, like GP40's for instance, yes they did have a front and back. Most RR considered the cab end, or short hood, to be the front, and even in cabless 'booster' locos this was still considered the front. Often times RR's would have the manufactorer (sticking with EMD here) actually move equipement around, such as moving the dynamic brakes to where the cab used to be. now them are kinda neat lookin. I will be going with newer engines as I'm partially making a fantasy RR, but I think I may turn my existing GP9 into a booster unit. I don't care if Milwaukee Road never did it, in my MILW world they did.
MILW-RODR Perhaps I should have mentioned this since your OP was about "B" units. If you are reffering to 2nd gen diesels, like GP40's for instance, yes they did have a front and back. Most RR considered the cab end, or short hood, to be the front, and even in cabless 'booster' locos this was still considered the front. Often times RR's would have the manufactorer (sticking with EMD here) actually move equipement around, such as moving the dynamic brakes to where the cab used to be. now them are kinda neat lookin. I will be going with newer engines as I'm partially making a fantasy RR, but I think I may turn my existing GP9 into a booster unit. I don't care if Milwaukee Road never did it, in my MILW world they did.
Perhaps you should have read the thread that the OP referred to in his opening line to understand that he is indeed talking about F7B units, not 2nd generation locomotives. Here is a link to the thread:
http://cs.trains.com/trccs/forums/t/152414.aspx
Don Z.
Research; it's not just for geeks.
Texas ZepherI am certain every possible combination existed; however, when the units were permanently coupled from the factory the general (default) configuration was "back to back".
That's interesting.
I usually see them coupled in photos as front-back. You can tell because the exhaust fans on the roof sit slightly stearnside of the engine. The exhaust side would be the "rear"
I wonder if they got switched around a lot. I've seen a lot of A-A units back to back.
Don - Specializing in layout DC->DCC conversions
Modeling C&O transition era and steel industries There's Nothing Like Big Steam!
GRAMRR Reading TrainsBuddy's post regarding back-up light placement on "B" units made me think of another question that I just took for granted. Apparently "B" units have a front and back end. Connected in an A-B configuration, are the engines oriented with both "front" ends facing in the same direction or are they connected "back to back?" What was general practice?
Some people have mentioned FT's. They are in some respects a special case, since they are asymetrical, theat is the distance from the truck center to the coupler is different on the front than on the back. they came in semi-permanently coupled pairs (back to back) so they pretty much had to always be joined the same way since it was physically impossible to connect them any other way.
Other F units were symeterical so there wasn't any difference which way they were pointed. While engines were assigned and operated as sequential sets they probably were always back to back since if they came from a set, they went back in the same set so there wasn't an opportunity to turn them. Once railroads split the sets up and did not try to maintain sequential sets, then it was whatever way the engines were available. Since it made no difference operationally, there is no incentive to try an turn them one way or another. I know that with hooded B units, neither the MP or UP attempted to keep them pointed in any particular direction.
Dave H. Painted side goes up. My website : wnbranch.com
I have plans to couple my A-B and A-A sets with a drawbar, thinking that they'll look better coupled closer together, and shouldn't give me any grief operationally. What do ya think?
while we are on the subject of "B" units, didn't some of the covered wagons have a hostler control station inside so they could be moved about independently?
grizlump
grizlump9 while we are on the subject of "B" units, didn't some of the covered wagons have a hostler control station inside so they could be moved about independently?
Yes, they did.
grizlump9 while we are on the subject of "B" units, didn't some of the covered wagons have a hostler control station inside so they could be moved about independently? grizlump
Some roads consider the end with the control stand as the front.
Of course railroaders had a hard time telling by looking.
So,some roads place a "F" on the front end of the "B" unit.
http://www.railpictures.net/viewphoto.php?id=178066&nseq=9
Larry
Conductor.
Summerset Ry.
"Stay Alert, Don't get hurt Safety First!"
BRAKIESo,some roads place a "F" on the front end of the "B" unit.
By Federal law ALL locomotives in the US have to have a F on the front end.
dehusman BRAKIESo,some roads place a "F" on the front end of the "B" unit. By Federal law ALL locomotives in the US have to have a F on the front end.
I don't think that was required on "B" units..
http://www.railpictures.net/viewphoto.php?id=168417&nseq=0
http://www.railpictures.net/viewphoto.php?id=264916&nseq=2
http://www.railpictures.net/viewphoto.php?id=182241&nseq=8
http://www.railpictures.net/viewphoto.php?id=88731&nseq=18
OK, with or without hostler controls, B units of cab type diesels do have a front and back.
In the case of all EMD F or E units, the end with the steam generator (or the space it would be in on F units not so equiped) is the rear. A and B units are layed internally the same starting at the rear. The B units simply don't have a cab at the other end. The prime mover (diesel engine) is not in the middle, but offset to the rear. So looking a the roof of any F or E unit, the fans are closer to one end than the other. The end they are closer to is the rear. EMD FB units with steam generators used some of the "empty" cab space up front for additional water tanks.
EMD encourged railroads to run them "back to back" for a number of reasons. In an AB set, if you had hostler controls, that did in effect give you control at both ends since the B unit hostler controls are just inside the "front" door.
Also, on E units or if your F units had steam generators, they would be near each other and would work more effiecently and made them easier to operate.
ALCO PA/PB units did not follow this design. Instead the steam generator on the PB was at the front, in place of the cab. So many roads prefered to run the both forward, again because this placed the steam heat equipment together. The steam generators did require some attention by the crew, so having them together was a good idea.
Most of this applies to the earliest use of these locomotives when they where generally thought of as "sets". As railroads interchanged the pieces of orginal "sets" of locomotives these "rules" may or may not have been followed, subject to a lot of different conditions on each road.
Sheldon
BRAKIE dehusman BRAKIESo,some roads place a "F" on the front end of the "B" unit. By Federal law ALL locomotives in the US have to have a F on the front end. I don't think that was required on "B" units.. http://www.railpictures.net/viewphoto.php?id=168417&nseq=0 http://www.railpictures.net/viewphoto.php?id=264916&nseq=2 http://www.railpictures.net/viewphoto.php?id=182241&nseq=8 http://www.railpictures.net/viewphoto.php?id=88731&nseq=18
Larry,
The first two pictures you linked to have a "F" on the end to your left, that is the front. And in my experiance many B units where so labeled.
DigitalGriffinI usually see them coupled in photos as front-back.
The only railroad that I know that consistently ran the "B" units in a forward direction is the NP. Once again this doesn't count the FTs and early permanently coupled F3 units. They are (at least all the pictures I can find and properly interpret) back-back.
I did look up some ABA combinations. The Santa Fe Alco P set #51 had the B unit back to back with the first A and then the last A in reverse. Technically then two of the three units were running backward.
The GN was really big with the semi-permanently coupled ABA sets. But amazingly of all the photos I have, none pictures are "as delivered" factory shots. I did find a picture where the B is running in the forward direction (on the point of the Western Star).
The bottom line for a modeler remains to do research on the specific prototypical road and time period.
As Sheldon implies, the later in time one gets the more loosey goosey one can get with the configurations. The Santa Fe for one reconfigured/renumbered the entire F unit fleet at least three times.
Interesting question, so I got all my books out on the D&RGW and found some photos taken by the EMD photographer. and it appears the ABBA sets delivered to the Grande, the b's are back to back which means the A and B of each end were facing the same direction.
Paul
Off Topic,but on the Norfolk and Western the F was almost always on the opposite end from the cab. Unlike most Railroads they ran them the RIGHT way!
ATLANTIC CENTRALBRAKIE dehusman BRAKIESo,some roads place a "F" on the front end of the "B" unit. By Federal law ALL locomotives in the US have to have a F on the front end. I don't think that was required on "B" units.. http://www.railpictures.net/viewphoto.php?id=168417&nseq=0 http://www.railpictures.net/viewphoto.php?id=264916&nseq=2 http://www.railpictures.net/viewphoto.php?id=182241&nseq=8 http://www.railpictures.net/viewphoto.php?id=88731&nseq=18 Larry, The first two pictures you linked to have a "F" on the end to your left, that is the front. And in my experiance many B units where so labeled. Sheldon
All of those locomotives have their front end away from the camera, which makes the F difficult to see. The NS unit actually has a yellow F on the white stripe, just to the left of the second grab iron from the left end. I am sure each ATSF unit has an F on it, but I cannot find them.
"No soup for you!" - Yev Kassem (from Seinfeld)
In any three unit lash up (ABA or ABB) one unit will obviously be different from the other two. In the case of an ABA, one AB is always back to back. Which way it is pulling the train has no bearing because the whole point of having A units on each end is to make the set bidirectional so it does not need to be turned.
Many roads, like the NP used their F units for pssenger. It would have made sense to put steam generator equiped B units back to back. ATSF only had steam generators or their B units, do to the greater water capacity, so in a ABBA unit set in those cases, they may have prefered the B units back to back, again, placing the steam generators near each other.
Atlanticcwntral has pretty much described any orientaion needed for a FB.
Although in any other use other than passenger where the steam generator/ water tank split between units, the B unit could be run in any direction.
B&O F3/7 passenger sets w/ steam generator required that the Bunit be positioned for steam gen coupling. These AB sets were ordered w/ steam gen in one ond water tank in other. Even some AA pass sets were done this way. The AA ran back to back though.
The front of the B unit is described by atlanticcentral, the blank section of the roof is toward the ft with fans to the rear. The dymamic fan or blanked plate (non dynamic) is to the front of the fans. These are the easiest stotting features to ditingish the orientation of the unit. Of course there are many other features as the door placement, hatches, grills etc. but the rooftop is what stands out the most.
Modeling B&O- Chessie Bob K. www.ssmrc.org
GRAMRR I have plans to couple my A-B and A-A sets with a drawbar, thinking that they'll look better coupled closer together, and shouldn't give me any grief operationally. What do ya think?
That's what I do. I find like with Stewart FT's they can be very close together using their drawbar, and yet take curves fine. I put a Walthers paper diaphragms on one of the engines, they're too close together to use/need two. With other F's I make drawbars from styrene.
I believe laws/regulations require all engines to have an "F" to mark the front of the engine. On a B unit connected by a drawbar to an A unit, it would be considered one engine so only the A unit would have to have an "F" on it, but if a B unit has a separate no. and couplers on both ends, I'd assume it would need an "F" too marking the front...not that it would necessarily run with the "F" being in front, but it would be a way to tell which end is which.
One factor on how a railroad would set up an A-B set is that going back to the FT's, passenger F's with a steam generator had the boiler in the space in the B unit where the cab would have been if it had been an A unit. By putting the engines 'back to back' the steam generator would be closest to the first passenger car, which might be an advantage as far as running steam lines back to the cars.
With an A-B-A set it wouldn't matter, as the B unit would be going forward as often as backwards. BTW the FTSB (FT Short Booster) that was used for A-B-A FT sets ordered by railroads, was symmetrical so didn't have the overhang the regular FT B units had...and they couldn't have a steam generator because they didn't have the room because they were also shorter than normal FT B's.
dehusman grizlump9 while we are on the subject of "B" units, didn't some of the covered wagons have a hostler control station inside so they could be moved about independently? Yes, they did.
I was going to bring up about the FT's B-Units not being symetrical which would have definitely prescribed the way it was mated to it's A-Unit--I am equally certain that someone will have a photograph of an FTB coupled-up in a loco lashup at least in a manner which I would consider to be "backwards."
One of the hobby magazines--MR I believe--had a photograph of one of these B-Units with a hostler hanging his head out of a window. I am certain that this would have been designated as the "front" of the unit but whether that would have mandated any specific coupling to an A-Unit I do not know.
This "BLOWHARD" OPINION is tendered in an attempt to HORNSWOGGLE the forum readership with prodigous quantities of completely INANE and absolutely MEANINGLESS INFORMATION: if I cannot dazzle with brilliance I will attempt to baffle with BS.
From the far, far reaches of the wild, wild west I am: rtpoteet
R. T. POTEET I was going to bring up about the FT's B-Units not being symetrical which would have definitely prescribed the way it was mated to it's A-Unit--I am equally certain that someone will have a photograph of an FTB coupled-up in a loco lashup at least in a manner which I would consider to be "backwards."
As has been pointed out, FT's where built as draw bar connected AB sets, back to back, as has been explained by myself and others. ABBA FT sets had couplers between the two B units, on the long end or front of each B unit.
Later, many railroads fitted their FT's all with couplers eliminating the drawbar connected AB sets, this would obviously then allow any position or arrangement.
ABA FT sets, as explained already where completely drawbar connected and used the FTSB B unit which was shorter and symetrical. Those too where often later fitted with couplers allowing any type of placement.
R. T. POTEET This "BLOWHARD" OPINION is tendered in an attempt to HORNSWOGGLE the forum readership with prodigous quantities of completely INANE and absolutely MEANINGLESS INFORMATION: if I cannot dazzle with brilliance I will attempt to baffle with BS.
???????????????????????????????????????????????????????????????????????????????
The answers to this question topic are highly dictated by when you are talking about - when these locos where relatively new OR when they had been in service for years/decades.
What's interesting is that Walthers sets forward direction on their Proto 2000 B units to move towards the "F" location. But I have seen now quite a few pictures of GN prototypes where AB sets are running back to back - you can easily see that their fuel tanks point in opposite directions.
I have a question about the number boards on F7A units. Does anyone know what color was the backlight on Great Northern diesels? Walthers ships them in white, just like headlight, but I've seen a person painting number board lights yellow.