IAFlyer Alright - heres the update that eveyone is chomping at the bit for..
Alright - heres the update that eveyone is chomping at the bit for..
Congrats!
Rich
Alton Junction
The DCC Booster from TAM Valley arrived. I installed it along with my OG-AR and my problem went away. Engine could go through either side of the Wye without shorting the DCC system out.
Thanks for all that helped with advice!
Now I just need to get the track maintenace gang out to repair minor trackwork issues (tortise adjustment, on another turnout a snap switch needs replacement, etc) and we'll be moving trains again.
Hang in there, Mike. The OP checks in a few times every month.
Well, I am a DC operator, not DCC, but if I interpret the original drawing correctly it appears that there should be insulated gaps in both frog rails of the diverging route of that crossover above the southern wye connection. One of the RED gaps appears to be in one of these rails but not in the other - the other RED gap appears to be in the right rail of the inner through circuit?
Mike
I'm here - I have been busy with dealing with the 'virus. I'm fine, just have the kids home and they take almost all the free time I have.
I have a DCC Booster coming in the next day or two. I decided that the low amperage of the DCC++ system (less than 2 amps) wasn't allowing the Auto Reverser to activate. So hopefully this will provide enough amperage to allow the AR to activate before the DCC shuts down for the short.
I'll update when I get it put in!
IAFlyer richhotrain For the OP, if that is the problem, the OG-AR will have to be replaced with something like a PSX-AR which has a trip current adjustment down to 1.27 amps. In that instance, if a reverse polarity short occurs, and the DCC++ has been programmed up to 1.6 amps, the PSX-AR will trip first at 1.27 amps before the DCC++ system can react at 1.6 amps. Here's an update: I rewired and created a small reversing section as I indicated in the last track diagram. Nothing changed - I could enter the reversing section just fine from one side, but as the engine exited the other side, the DCC system shut down, like it shorted out. I checked all the feeders to the "yard" and none were connected incorrectly. As Rich pointed out, the OG-AR activated at 4 amps, but my DCC is only putting out about 1.6amp, so it likely that the DCC shorts out first. That's why when I reverse the leads, it works the other way (Because the reverser never reverses) I looked into making or buying a booster, but that seems either out of my skill set (making) or too expensive (buying), I'd just get a different DCC system if I was going to get a booster. So, the plan is to rewire it a-gain - it's not hard, just moving some insulated joiners, and a little bit of wiring underneath. I'll also get adjustable auto reverser like the PSX-AR or AR-1, to replace the OG-AR. Thanks to all.. I hope this fixes the problem!
richhotrain For the OP, if that is the problem, the OG-AR will have to be replaced with something like a PSX-AR which has a trip current adjustment down to 1.27 amps. In that instance, if a reverse polarity short occurs, and the DCC++ has been programmed up to 1.6 amps, the PSX-AR will trip first at 1.27 amps before the DCC++ system can react at 1.6 amps.
Here's an update:
I rewired and created a small reversing section as I indicated in the last track diagram. Nothing changed - I could enter the reversing section just fine from one side, but as the engine exited the other side, the DCC system shut down, like it shorted out. I checked all the feeders to the "yard" and none were connected incorrectly.
As Rich pointed out, the OG-AR activated at 4 amps, but my DCC is only putting out about 1.6amp, so it likely that the DCC shorts out first. That's why when I reverse the leads, it works the other way (Because the reverser never reverses) I looked into making or buying a booster, but that seems either out of my skill set (making) or too expensive (buying), I'd just get a different DCC system if I was going to get a booster.
So, the plan is to rewire it a-gain - it's not hard, just moving some insulated joiners, and a little bit of wiring underneath. I'll also get adjustable auto reverser like the PSX-AR or AR-1, to replace the OG-AR.
Thanks to all.. I hope this fixes the problem!
rrinker The OG_AR he has will trip before that booster, PLUS he will be able to run more locos than the 1.6 amp capacity of the DCC++ board. This assumes the issue is the moto shield used in the DCC++ setup is trippig before the OG-AR due to the low current output. --Randy
The OG_AR he has will trip before that booster, PLUS he will be able to run more locos than the 1.6 amp capacity of the DCC++ board.
This assumes the issue is the moto shield used in the DCC++ setup is trippig before the OG-AR due to the low current output.
--Randy
Modeling the Reading Railroad in the 1950's
Visit my web site at www.readingeastpenn.com for construction updates, DCC Info, and more.
rrinkerTam Valley has a 3amp continuous/5amp trip booster for $1 more than the price of a PSX-AR.
You lost me. What I see is a trip booster board without a power supply and without reversing capability. How does that help the OP?
2nd product down http://tamvalleydepot.com/products/dccbooster.html
Henry
COB Potomac & Northern
Shenandoah Valley
Tam Valley has a 3amp continuous/5amp trip booster for $1 more than the price of a PSX-AR.
Just saying.
IAFlyer, before you buy a new AR, or booster, or DCC system, try this.
If you are certain of your gaps and wiring, disconnect the OG-AR and install a DPDT (double pole double throw) toggle switch for manual control. Connect the two input wires from the bus to one end of the DPDT and connect the two output wires to the center terminals on the DPDT. Then, as the loco approaches the short reversing section, throw the DPDT to match up the polarities. It should work if the gaps and wiring are correct. If it works, you know that the OG-AR is the problem.
Edit Note: If you buy a new AR, spend the extra money and get the PSX-AR. The AR-1 has a mechanical relay and does not interact well when there are solid state devices on the layout. The mechanical relay is too slow and you will have similar performance problems as the OG-AR, but for different reasons.
richhotrainFor the OP, if that is the problem, the OG-AR will have to be replaced with something like a PSX-AR which has a trip current adjustment down to 1.27 amps. In that instance, if a reverse polarity short occurs, and the DCC++ has been programmed up to 1.6 amps, the PSX-AR will trip first at 1.27 amps before the DCC++ system can react at 1.6 amps.
Mike, at this point we still cannot be sure whether the problem is the gapping and the wiring or the OG-AR until we hear further from IAFlyer.
But here is the issue with reverse polarity shorts. When a reverse polarity short occurs, the current draw can be high, well in excess of 5 amps. Take the NCE Power Pro as an example. It has a 5 amp booster. So, without any other protection, the Power Pro will shut down if the current draw exceeds 5 amps. An NCE Power Cab on the other hand is a 2 amp system and so it will shut down if the current draw exceeds 2 amps. A DCC++ system has a limit of 2 amps but "out of the box", it only draws 0.8 amps, so it will shut down if the current draw exceeds 0.8 amps. Apparently, the DCC++ system can be programmed up to 1.6 amps.
Now, enter the auto-reverser. An OG-AR is a 4 amp circuit breaker/auto-reverser. When a reverse polarity short occurs, the OG-AR will shut down the system if the current draw exceeds 4 amps. But if the OG-AR is part of a DCC++ system, the DCC++ will react as soon as the current draw exceeds 0.8 amps and shut down the system before the OG-AR reacts to the short. The OG-AR does not have a trip current adjustment, so it will only react when the current draw is 4.0 amps or greater.
For the OP, if that is the problem, the OG-AR will have to be replaced with something like a PSX-AR which has a trip current adjustment down to 1.27 amps. In that instance, if a reverse polarity short occurs, and the DCC++ has been programmed up to 1.6 amps, the PSX-AR will trip first at 1.27 amps before the DCC++ system can react at 1.6 amps.
richhotrainThe other possibility is that the DCC++ is reacting faster than the OG-AR, resulting in a short since the polarities remain mismatched.
Is that like Randy mentions in his post? The DCC++ is shutting down before the AR.?
Watching and learning...
Mike.
My You Tube
BigDaddy I vote for everything "West" I'm not sure why you original setup did not work unless it is incompatibility with the DCC ++ system
I vote for everything "West" I'm not sure why you original setup did not work unless it is incompatibility with the DCC ++ system
One possibility is that feeders from the output side of the OG-AR are connected to the mainline.
The other possibility is that the DCC++ is reacting faster than the OG-AR, resulting in a short since the polarities remain mismatched.
If IAFlyer reports back that a short is stilll occurring, one workaround would be to disable the OG-AR and install a DPDT toggle switch to manually flip the polarities. If that solves the problem, then the long term solution is to replace the OG-AR with a PSX-AR.
IAFlyer So is there agreement that I can use everything "west" of the original yellow colored gaps (on the first track plan) on the divergent ends of the four mainline turnouts as one big reversing section? I do agree that's the best for the train length, as the small reversing sections will be way too small.
So is there agreement that I can use everything "west" of the original yellow colored gaps (on the first track plan) on the divergent ends of the four mainline turnouts as one big reversing section?
I do agree that's the best for the train length, as the small reversing sections will be way too small.
richhotrainI'm not sure your new reversing section is long enough, if you are running metal wheel rolling stock. It should be longer than your longest train. If he just leaves the gaps (yellow colored) on the divergent ends of those four mainline turnouts, he should be good to go because everything west of the mainline will be part of one large reversing section. Edit Note: Henry, I see what you are referring to. In his reply to florida flyer, he illustrated a short reversing section on the North leg of the wye and removed the gaps on the South leg. I agree with you that the resulting reversing section would likely be too short.
If he just leaves the gaps (yellow colored) on the divergent ends of those four mainline turnouts, he should be good to go because everything west of the mainline will be part of one large reversing section.
Edit Note: Henry, I see what you are referring to. In his reply to florida flyer, he illustrated a short reversing section on the North leg of the wye and removed the gaps on the South leg. I agree with you that the resulting reversing section would likely be too short.
BigDaddy I'm not sure your new reversing section is long enough, if you are running metal wheel rolling stock. It should be longer than your longest train.
I'm not sure your new reversing section is long enough, if you are running metal wheel rolling stock. It should be longer than your longest train.
I agree with Rich about not needing gaps on Atlas turnouts and have nothing on DCC++
IAFlyer richhotrain I am not familiar with the term "frog on frog" short, but I don't see any reason for those two single rail gaps (colored red) on the mainline crossover. I got the concept of "frog on frog" from this MR page: https://mrr.trains.com/how-to/dcc-electrical/2010/01/how-to-wire-power-routing-model-train-turnouts
richhotrain
I am not familiar with the term "frog on frog" short, but I don't see any reason for those two single rail gaps (colored red) on the mainline crossover.
I got the concept of "frog on frog" from this MR page: https://mrr.trains.com/how-to/dcc-electrical/2010/01/how-to-wire-power-routing-model-train-turnouts
IAFlyer richhotrain I have no working familiarity with the DCC++ base station and controller. How many amps is that system?
I have no working familiarity with the DCC++ base station and controller. How many amps is that system?
richhotrainIAFlyer, apparently your posts are delayed. I just saw your two most recent replies.
richhotrain The four divergent ends that I was referring to were #2, #3, #4, and #5. You already showed those four divergent ends as gapped, and I agree that the gaps are properly placed there. I see from your latest track diagram that the mainline gaps (colored yellow) have been removed, and I agree with that removal since there is no need for gaps at that point. I can't speak for Florida Flyer, but I believe that your assumption is correct that he was suggesting a short reversing section. My reaction is to leave everything west of the mainline as one big reversing section. I am not familiar with the term "frog on frog" short, but I don't see any reason for those two single rail gaps (colored red) on the mainline crossover. Are you certain that all of the feeders from the output side of the OG-AR are wired to rails inside the reversing section, west of the mainline?
The four divergent ends that I was referring to were #2, #3, #4, and #5. You already showed those four divergent ends as gapped, and I agree that the gaps are properly placed there. I see from your latest track diagram that the mainline gaps (colored yellow) have been removed, and I agree with that removal since there is no need for gaps at that point.
I can't speak for Florida Flyer, but I believe that your assumption is correct that he was suggesting a short reversing section. My reaction is to leave everything west of the mainline as one big reversing section.
I am not familiar with the term "frog on frog" short, but I don't see any reason for those two single rail gaps (colored red) on the mainline crossover. Are you certain that all of the feeders from the output side of the OG-AR are wired to rails inside the reversing section, west of the mainline?
I got the concept of "frog on frog" from this MR page: https://mrr.trains.com/how-to/dcc-electrical/2010/01/how-to-wire-power-routing-model-train-turnouts I don't have Model Railroad going back that far, so I'm not sure if it was part of a larger article about wiring. The problem is I'm using an old track diagram designed for DC wiring and trying to make it into DCC - as a beginner!
richhotrain I have no working familiarity with the DCC++ base station and controller. How many amps is that system?
I'll finish up the wiring and report back on the success or lack of.
iaflyer
IAFlyer I looked at the area west of the yellow marked insulators as one big "reversing section." I am using Atlas crossings as well. Rich, when you are talking about "the divergent ends of each of those four mainline turnouts" are you talking about the turnouts marked 17N and 17R? FloridaFlyer, you are talking about creating a small reversing section, like the image below? (R being the new short reversing section). The red insulators in this image, I think are needed to prevent a "frog on frog" short. (I don't have a lot of posts, so my posts are delayed)
I looked at the area west of the yellow marked insulators as one big "reversing section." I am using Atlas crossings as well.
Rich, when you are talking about "the divergent ends of each of those four mainline turnouts" are you talking about the turnouts marked 17N and 17R?
FloridaFlyer, you are talking about creating a small reversing section, like the image below? (R being the new short reversing section). The red insulators in this image, I think are needed to prevent a "frog on frog" short.
(I don't have a lot of posts, so my posts are delayed)
IAFlyer I'm using the OG-AR with a DCC++ controller (connected to JMRI). I have the power coming into the OG-AR from the main power bus, and it goes out to a power district that is powering everything "west" of the yellow insulators.
I'm using the OG-AR with a DCC++ controller (connected to JMRI). I have the power coming into the OG-AR from the main power bus, and it goes out to a power district that is powering everything "west" of the yellow insulators.
The reason certain ARs don;t work with some lower powered systems is that the minimal trip current of the AR is above the rating of the system. So the DCC system will cut out before the AR swaps the outputs. Not always - which is even worse than if it failed every time. It might work with certain locos in certain combinations but then a different loco causes the whole system to short instead of the AR.
For an AR to work, it has to trigger faster and at a lower current that the system booster, otherwise it will be like the AR is not even there.
This layout is a bit more complex than just a simple wye - there are two wyes. Typically with a wye, you just need to isolate one leg. For a simple wye - 4 insulated joiners. On both rails of both diverging legs of the turnout for the leg you are connecting the AR to.
That the OP says it works if swapping the wires - it may just be that the rest of the tracks aren't all wired in the correct phase.
Mark R. Everyone's replies are assuming the AR module is actually functioning correctly. It sounds to me like it's not .... especially the comment about switching the wires and the other leg works correctly. I'd be looking at the AR module and verifying it's actually doing what it's supposed to be doing first. The original description of the problem tells me it isn't.
Everyone's replies are assuming the AR module is actually functioning correctly. It sounds to me like it's not .... especially the comment about switching the wires and the other leg works correctly. I'd be looking at the AR module and verifying it's actually doing what it's supposed to be doing first. The original description of the problem tells me it isn't.
From what I read, the OG-AR has two outputs: Rail 1 and Rail 2. Rail 1 connects to DCC 1 in normal and DCC 2 when the OG-AR is reversed. Rail 2 connects to DCC 2 in normal and DCC 1 when the OG-AR is reversed. (DCC 1 and DCC 2 are references to the two leads on the input side of the OG-AR).
Here is how Tony's Trains describes the operation of the OG-AR:
The On Guard auto-reverser (OG-AR) can be used to automatically route power to the frog. In addition to the auto routing of power, it also provides a circuit breaker function to protect the switch and your equipment in the event of a derail on the frog.
Note that when the OG-AR senses a frog in the wrong polarity, BOTH outputs reverse. This is because the OG-AR is originally designed as a reverser, but a frog controller is simply a one rail reverser.
Hence, for the given route, you can predict the polarity required of each frog. Start with the first switch and pick, say, the Rail 1 output. For each switch in the route, decide if it is in phase or out of phase with the first switch. If in phase, connect the frog to Rail 1. If out of phase, connect the frog to Rail 2. Now, when the first frog is touched, all the frogs in the route will be correct. Each switch, if crossed individually, will still flip its frog to the correct phase as required.
The OP is not powering the frogs, so at first glance, this all seems irrelevant. But the fact that the OG-AR is polarity specific leads me to believe that the OG-AR is probably not defective but rather is trying to resolve multiple reverse polarities. It seems to me that this can occur if the reversing section is miswired or misgapped or both.
That's why the OP ought to eliminate those mainline gaps and also check to see if any feeders connected to the output side of the OG-AR are wired to the mainline.
mbinsewi I've been following along, dumb question....for DCC AR function, don't both rails have to be gapped? Mike.
I've been following along, dumb question....for DCC AR function, don't both rails have to be gapped?
BigDaddy Before Mark's comment, I considered whether one side of the OG-AR might not be functioning to detect shorts and rejected it for no good reasons. I found several comments on the Internet about it not working with the Power Cab but I'm not clear on why. One pundit said it was faster than most reversers. I suppose one could built a short section of gapped track and test it. If the OP has a Power Cab or Zephyr, he's up the creek.
Before Mark's comment, I considered whether one side of the OG-AR might not be functioning to detect shorts and rejected it for no good reasons. I found several comments on the Internet about it not working with the Power Cab but I'm not clear on why. One pundit said it was faster than most reversers.
I suppose one could built a short section of gapped track and test it. If the OP has a Power Cab or Zephyr, he's up the creek.
Presumably, the OG-AR is incompatible with the Power Cab because the Power Cab has a 2 amp booster and the OG-AR is a 4 amp circuit breaker, so the Power Cab booster trips before the OG-AR. Whereas the PSX-AR has a trip setting adjustment down to 1.27 amps, making it ideal for the Power Cab, I don't believe that the OG-AR has a trip setting adjustment. Of course, this all assumes that the OP is operating with a low amp DCC system. We need to hear back from him.
OK, thanks, I figured so, just had to ask. I don't have any reversing sections on this layout, on my previous DC I did.
After looking at his plan, I see the little boxes at some of the joints must be the locations for gaps for using DC cab control, as the plan was drawn for.
I'll shut up and keep watching. Waiting for the OP's reply.