Dampfmann wrote:I have some digital pictures to share. I read the "How to Post Pictures" thread at the beginning of the forum, but it didn't make much sense. I'm rather new at this so can anyone give the "For Dummies" version of posting pictures. Right now they are on my camera, but I can easily move them to iphoto. What's next?As far as the copper contacts, I didn't see any loose wires or anything else that might cause a potential short. When I took the top of the coach off and peered inside, I found more fried wires. I want to post the photos so you can see the actual wiring for yourselves. Someone inquired about crossing between blocks/ovals. Nope. Each oval is independent-- no crossing over. Nothin' too exciting.Martin
Brent
Bob Nelson
Now it sounds like you have a dead spot or compromised center rail connection somewhere in the loop for the PE, as it certainly seems that the power for the loco & smoke unit is being drawn through the car wiring at some point.
Try running just the engine at a fairly low speed around the layout and see if there are any obvious power drop-outs. There could be loose pins or connections on O-27 or FasTrack.
Rob
Dampfmann wrote: Okay, here is some more information. I don't have an extravagent layout... yet. Until I get to that point I am running my trains in ovals around a 4' x 8' table. Each oval is its own block. The most voltage I run any train is about 16 volts. Any faster and they start flying off the track.
Okay, here is some more information. I don't have an extravagent layout... yet. Until I get to that point I am running my trains in ovals around a 4' x 8' table. Each oval is its own block. The most voltage I run any train is about 16 volts. Any faster and they start flying off the track.
I am surprised that you can get anywhere close to 16 volts running a conventional engine. I'm wondering if you might have a problem with the engine that it is requiring such a high voltage.
Earl
Martin, here's a shot out of the dark since you've already got the for repairs.
I'm a low-end do-it-yourself expert. Yes, I agree the companies do use very thin wire. It is not always the gauge of the wire, but the amount of actual stranded metal inside the wiring. There are times where the outside of the wire looks good, but inside there's a break.
This happened to me once and might have been your trouble. Pop the roller pickup assembly off the car using a straight edge screw driver. It pops off quite easily. On the underside you will see two strips of copper metal riveted to the pplastic assembly. One piece goes to the roller pickup of the center rail and is folded with a small slot for the roller pickup. One piece is longer and goes to the wheel axles on each side of the plastic assembly.
Notice each piece of copper has a fold: The one for the roller pickup is on the far back end. The other has the fold midway alongside the other piece of copper for the roller pickup. Two things could be happening here. One is the the wire soldered to the wheel axle pickup has either solder or a couple strands of wire that is touching the other pickup. The other is that the fold of the axle pickup copper piece is making contact with the other center rail copper piece. If the fold on the axle pickup is angled, it is possible for the roller itself to hit this when the train is on the track. Intermident contact between these two piece might not be enough to short the train or trip the circuit breaker, but it could VERY easily heat up the wires very quickly.
This happened to me once, and I bent the pickup contacts a little and the problem went away immediately. I strongly suspect this could be your problem.
brianel, Agent 027
"Praise the Lord. I may not have everything I desire, but the Lord has come through for what I need."
Again, I am using a ZW transformer and have not had this problem with any other cars, just the PE coaches. I have had the wires burn using both O-27 and Fastrack.
I contacted Lionel about this problem and they told me to take the coaches to the authorized repair shop in my area. The woman I spoke to on the phone in the "tech dept." was of little help at all.
I took the cars to the local repair facility. I haven't heard back from the hobby shop about what they think is the cause of the melted wires. When I do, I'll pass this information along.
In the mean time, I think the gauge of the wires is too thin. They are about as thick as a piece of angel hair spaghetti. It certainly isn't as thick as the wiring on other post-war cars I have. If you have PE coaches, do yours have wire that is equally as thin. (I'll have to measure the exact gauge when I'm at home).
Still puzzled...
Martin
I was hoping to get a response from Martin (Dampfmann) before diagnosing this; but he seems to be gone. If Marty is right, this would be an example of the sort of bad stuff that happens with that kind of operation, against which I preach all the time.
If one is adding bridge rectifiers to lighted cars, I recommend also putting in an electrolytic capacitor to keep the voltage up over any interruptions that do occur. In fact, I find that only one pickup works pretty well with a rectifier and a capacitor and have removed pickups to reduce the drag on some of my cars, although there is some chance of a car's lights going out when the train stops.
MartyE wrote: Are you crossing between 2 blocks that maybe out of pase or not evenly powered?
Are you crossing between 2 blocks that maybe out of pase or not evenly powered?
Marty has hit it exactly on this one. In order to eliminate bulb flickering, the pickups on the PE cars are connected, and are of a small gauge spec'd for the bulbs only, not the loco, the other cars, and all of the accessories & switches using track power, which is what is happening when the trainset traverses blocks set at different voltages.
The easy fix is to install a tiny full-wave bridge(less than 1 amp is fine) powered by each pickup & ground on the AC side, or 2 per car, and tie together the "+" outputs to each other, and the "-" outputs to each other, effectively running the lights on the DC outputs & blocking any back-feeding of current from one truck to the other.
Single diodes in-line with the center rail pickups will work too, for half-wave current to the lights. This is probably what Lionel should have done had they considered this possibility.
I would suggest this is an isolated incident. I have the PE cars and run them heavily during the holidays and haven't had an issue nor have I heard of this before in the 3 years they have been out on any of the boards.
Any more details you could give us? Are you crossing between 2 blocks that maybe out of pase or not evenly powered?
Trying to update my avatar since 2020
MartyE and Kodi the Husky Dog! ( 3/31/90-9/28/04 ) www.MartyE.com My O Gauge Web Page and Home of Kodiak Junction!
Dampfman,
If the passenger cars are new I would suggest getting in touch with the warrenty department and asking for help!
The problem may be that the manufaturer used a very small wire that can not take the current draw for the light bulbs, try replacing the wire with a larger size wire and that should help with heating up. Reason for using a small wire is production cost per hundred units sold, if they can save 30 cents a car times 1000 that is about $300.00 savings to the manufacturer, that is done in automotive assembly lines here in the U.S.
Lee F.
Are the circuit breakers tripping on the power supplies? Do the lights in the coaches ever actually light? Make sure the lights are actually in the circuit. You could also remove the bulbs and see if the wires still get hot. If they do, that would suggest a short or a mis-wired coach.
The problem must be in the coaches because if you were supplying enough voltage to melt the wires under normal circumstances, the engine would be flying off the track. I would look for a pinched wire somewhere or some other form of short.
I'll be able to accurately answer this question and describe the pick-ups when I get home. Heck, I might even try to post a picture or two. You gotta try sometime...
I am experiencing a problem with my Polar Express coaches. The wires leading into the carbody from the electrical pick-ups continue to melt. They get hot enough to melt the insulation on the wires and any plastic parts they come into contact with. I have had this problem using two types of transformers: a ZW and the cheap one that comes with the RTR train sets. I have used Fastrack and tubular track.
Before anyone tells me the problem must be with the transformers or the track, let me add one more bit of information to the puzzle-- I have not had this happen to any other, older Post-War lighted passenger cars.
Has anyone else experienced this problem? Could this be a mechanical/design defect with the coaches? I am interested to hear your theories.
Sincerely,
Our community is FREE to join. To participate you must either login or register for an account.
Get the Classic Toy Trains newsletter delivered to your inbox twice a month