Thanks to all for the replies. They have provided some options and possible solutions for this problem. As shown, it seems to have some unexpected weathering qualities as well.
This phenomenom can be found with the search terms: "spray paint" humidity blushing blush.
I think the result of this discussion is don't spray paint with high humidity.
Ed
This is a real issue in South Florida where the humidity is very high for 7-8 months out of the year. We cannot spray Testors 1260 Dullcote for weeks at a time or the dreaded white haze will be the result.
.
The good news: The problem is easily fixed most of the time. Just wait for a dry day, give the can of Testors Dullcote a real good shake, and spray on a light coat onto the effected model. It should be OK.
to the Model Railroader forums.
Good luck!
-Kevin
Living the dream.
As others have said, I have found it to occur in high humidity, and occasionally use this feature for factory painted locos.
It pays to make sure the dullcote is properly mixed prior to decanting to thin and stays mixed while airbrushing. The talc settles out if it sits.
Matthew
Can be caused by a couple things - most common is humidity. Another cause is the talc to carrier ratio is too high - the talc doesn't get fully immersed in the carrier on the surface and the result is you are seeing the dried talc.
Another coat of finish or even a straight shot of thinner will make it disappear.
That being said, that white haze can also be a very convincing weathering effect once you learn how to control it. This is a factory painted Athearn Genesis that was faded using the hazed dullcoat as the base fade ....
Mark.
¡ uʍop ǝpısdn sı ǝɹnʇɐuƃıs ʎɯ 'dlǝɥ
Thanks for all of the replies. I live in north Florida and the weather was rather damp on that occasion. The project was a previous coal hopper which was painted with scalecoat 2 and completely dry. I sometimes blend glosscote and dullcote to get various satin finishes however this was straight dullcote purchased in about 2015. I have noticed that there seems to be some additive (perhaps talc) that I try to mix completly. I think that I will repaint this car under different conditions and see what happens. I have noticed that scalecoat now has their own brand of clearcoats which may prove to be more consistent.
Alcohol on top of Dullcote, turns white, but that is not what you described. Dunno.
Henry
COB Potomac & Northern
Shenandoah Valley
I've also had the problem with humidity. I sprayed two identical shells outside on two different days, from the same rattle can. The humid day produced a milky result, while the dry day did not.
I kind of liked it. One just looked cleaner than the other.
It takes an iron man to play with a toy iron horse.
Ever notice when you release the valve on the bottom of the air tank there is some moisture that comes out? Do you have a water/moisture trap on the line between the compressor and the air gun? Not critical when spraying acrylics, but important when spraying solvent paints. Under pressure water/moisture mixed with solvents form emulsions, which can be milky.
Robert
LINK to SNSR Blog
I had that issue once apon a time Using testors laquaer. Found it was the mixing ratio of thinner to base. Also type of thinner and base. If they are not from the same producer, they dont always play well together with the clear Coat. Since you are using automotive laquaers, all i can say is paint big piece of scrap plastic. And start mixing clear coats. Starting at 20/80 and working up by 10s. 30/70, 40/60 and so on. make sure to divide the plastic sheet and mark off the section with the ration so you can watch over time what happens. That what i had to do to finally find the right ratio so that didnt happen
Wolfie
A pessimist sees a dark tunnel
An optimist sees the light at the end of the tunnel
A realist sees a frieght train
An engineer sees three idiots standing on the tracks stairing blankly in space
I had an issue with rattle can stuff doing that. I had left the can out in the garage and it was cold when I used it. I went in and got my other can that had been kept in at my hobby desk and it was fine. I had bought both cans at the same time. Being cold and/or constant temperature swings were probably the cause of the problem.
Brent
"All of the world's problems are the result of the difference between how we think and how the world works."
Interesting.....I am not sure as I know enough about model painting to be dangerous, but I think most dull lacquers have talc added as the dulling agent. I have found inconsistencies in Dullcote over the years.....so much so, that I stopped using it. It seems to work OK on wood, but on smooth surfaces such as painted brass or styrene, sometimes you'll get spots or talc stains. Both airbrushing and rattle cans caused this condition, but airbrushing a bit better as thinner was added.
HZ
I would agree that high humidity can cause this. It has happened to me when I used the rattle can in my shed early in the day when it was foggy outside. I applied another coat later in the day when the humidity had decreased and the milkiness disappeared.
to the MR Forums, Charles!
I've never had that problem airbrushing Dullcote, and have always used lacquer thinner, although perhaps 1/3 thinner to 2/3 Dullcote, and a little lower pressure - depends on the results I want for any particular project.I've read that alcohol can turn already-applied Dullcote white, but that effect can be negated by another overspray of Dullcote - that doesn't appear to be the situation here, though.What type of paint did you use? Some paints dry rather quickly, but take longer to fully cure. It used to be said that the "sniff test" will tell you if the paint is fully hardened, but many of today's acrylics have very low odour, even from an open bottle.
I usually wait several days after painting to apply any clear coats, especially if I'm using lacquer-based over water-based paints.
Wayne
are you painting over acrilics , enamal or other laqure ?
how long are you waiting to clear coat ?
what thinner are you using ? fast / medium/ slow
air pressure sounds a bit high , try lowering pressure.
I sorta slightly recall that it's been noted that high humidity while spraying clears can cause this problem. I repeat: sorta slightly recall.
The pressure is higher than I use, though I don't see why that would do it. I spray at around a start of 15 psi.
Regarding the talc comment, above. I think it's "always" in clear flat. The talc, or whatever other substance is used, creates the flatness. I've been known to let the clear-flat settle in the bottle, and pour off some of the clear. This makes the coating more flat.
It seems odd that I do NOT have this problem with spraying Dullcote "pure" out of a rattlecan. Is your DullCote very old? I ask that because some years ago I believe they changed the formula for the stuff. If I recall right the "old" DullCote had talc suspended in the clear medium. Sometimes you would get milky or unpredictable finishes from that stuff.
Dave Nelson
Hi. I have had some unpredictable results when airbrushing dullcote lacquer coatings and was interested to know if anyone else has had this problem and found a cure. I mix this product one to one with automotive lacquer thinner. It goes on wet and smooth but dries to a milky whitish finish. My air pressure is 30 psi which works well for all of my other paint coatings. I wonder if some other type of non lacquer based clear coat would be better to use. Thanks for your comments.