Darth Santa Fe:
Being a devoted fan of your engineering skills I would be very interested in seeing what you come up with. And, if I can really go out on a limb here, I would love to see an explanation of the process that you use to design the drive system. In my wee brain I can see a logical format for the arrangement of the parts but how the heck do you decide on gear sizes and ratios? I have glanced at NWSL's charts but I'm afraid they make my eyes glaze over. I would love to understand the process better!
Dave
I'm just a dude with a bad back having a lot of fun with model trains, and finally building a layout!
It returns! Glad to see my work is appreciated!
artguy, I also have one of those Mack railbuses I've been planning to build, but haven't started yet since the new FLEA is still in development. I've been checking with NWSL now and then, and progress has been slow due to a lack of funds, but they're really working to make it the best version yet (metal bearings finally!). I'm sort of past my project finishing window for now since the weather's cooled down over here (can't paint properly when it gets cold), but I've looked over the thing and can at least offer advice for now. Or, if you don't mind me not painting it, you can send me a PM about at least partially building it with a custom made drive unit.
(to send a PM, click on my name and then look for the "Start Conversation" button)
_________________________________________________________________
That's some cool stuff. I do love me some critters.
Hmm, perhaps I should build something small, model just one industry, that uses some small critters for intra-plant switching. Thus all I need is the 'interchange track' with the big railroad, and a critter or two, just swap them out when I get bored with one.
Hard do justify critters on the big railroad, even though PRR had a bunch of 44 Tonners, as did New Haven - but those are downright huge by the standards of a little 10 ton Mack
Oh yeah, also gives me something to use those Atlas #4's from the current layout on, since I won't have anything less than a #6 on my 'big' layout, and they will be Peco.
--Randy
Modeling the Reading Railroad in the 1950's
Visit my web site at www.readingeastpenn.com for construction updates, DCC Info, and more.
Applause!!!
Awesome ingenuity there!
Karl
NCE über alles!
Artguy:
NWSL (North West Short Line) has a power kit called the "Flea" which is ideal for your situation. Unfortunately the website says they are undergoing a redesign and are not currently available. You might find one if you watch eBay, although there aren't any currently listed there.
Here is a thread with a couple of similar projects. The rail truck is mine made using a really old motoring kit that I came across on eBay. Further down there is a Mack Railbus using the Flea drive:
http://cs.trains.com/mrr/f/88/p/217595/2397429.aspx#2397429
Here is NWSL's website:
http://www.nwsl.com/Home_Page.html
My Email address (for the Mack railbus ) is: artguy@frontiernet.net
Dear Darth, I just bought a Jordan, 1922 "Mack" railbus. I just can't seem to locate anyone who has it powered. You seem to have the knowhow and talent to do this. I would gladly pay you to build this "powered" railbus for me. I was thinking about powering the 2 REAR spoked wheels which are plastic. (I have 2 "metal" spoked wheels and axle to serve as the electrica pick up, now). Obviously a gear mechanism would have to be attached to the axle. Maybe I can build it myself with your advice? I'd rather have you build it for me, though. Please let me know what you think. Thanks! -artguy
Fantastic Darth! You're a genious! -artguy
Looks great Darth!
Painting the chassis black is a great idea to help hide the visible parts inside the cab.
I just received the #158 couplers and boxes for mine so it will soon be back on the workbench to have them installed.
Great job as usual Darth!
Whats your next project?
"The true sign of intelligence is not knowledge but imagination."-Albert Einstein
http://gearedsteam.blogspot.com/
That is a really nice model!!!Great Work!!
Now all it needs is a couple of the BullDog Hood ornaments off an Ath Mack!!Hmmm.....
After waiting some months for good painting weather (it's been brutally hot until recently), I've finally gotten this project finished!
All finished! Coupler mounting was difficult, but I managed to squeeze Kadee #158 Whisker couplers in there. The all metal body makes this heavier than my other critters, so it's the strongest puller of all my very small switchers (it can pull about 6 full sized cars). It's also very quiet and smooth, and is my best runner next to the Grandt Line Boxcab with NWSL gearing and a big coreless motor (still in progress).
It just so happens that I did use that size! And the tubing has a 3/32" inner diameter. So if you have both of those (as well as some sheet brass for the motor mount), you're good to go on stock materials!
Darth
One more question if I might - is the brass stock used for the chassis 3/16" x 3/8" ( .1875" x .375")? I'm hoping so because I have that size on hand.
All of the parts (including the brass stock, but minus the actual kit) came up to about $70. Pretty expensive, but still cheaper than the pre-built drives like the Bull Ant or Stanton. It costs to get real quality, but it sure makes a better unit than cheaper parts.
Great Job! I too have one of these Mack units. I was looking at it the other day wondering just how to go about powering it.Thank You so much for posting this. Now for the kicker. How much were the parts?
Ron
Thanks again
You're not being a pest, Dave.
To position the idler axles, I placed the gears without their axles on the side of the chassis, visually positioned them where I wanted, and used the position to make a small starting point for the drill. After the holes were drilled, I mounted the gears to check their mesh, took them back out, and elongated the holes in the direction needed to correct the mesh. Once everything was right, I powered up the mechanism to check where everything needed to go, and fixed it exactly in the position needed with either solder or glue (soldering was only done with the gears out to avoid melting the plastic). Most of the work was visual, and more of it had to do with listening and feeling, and only the axles had an actual measured point to be drilled (the spacing had to be exactly 24.5mm). Not exactly the most professional methods, but they work for me.
Darth Santa Fe
Thanks for the parts list.
Please let me ask a few detail questions:
- You obviously used the wheel base of the 15 tonner to determine your axle spacing. You also adjusted the height of the idler gears above the axles to make them fit between the axles. You said that you installed the center gear last, but you must have had some means of determining the offset for the intermediate idler gears. How did you determine the position of the idler gear axles? If it was guess work just admit it!
- You also managed to assemble all of the axle and idler gear bearings so they were in line with each other. Either you have a very keen eye (which I suspect) or you have a method for alignment. How did you do that?
Hope I am not being a pest.
Thanks for any insight. This is exactly the type of challenge I have been looking for.
Thanks everyone! I actually wasn't expecting to get so much response so quickly!
hon30critterI have the Mack kit. Any chance you could provide a list of part numbers and hints on how you built the drive?
The NWSL parts I used are:
12024-6 24 tooth 72DP wormgear (all gears are Delrin 72DP)18015-6 15T spur gear (two of them)18020-6 20T spur gear (three of them)10000-6 steel worm10165-9 1 x 2.4mm shaft adapter bushing (to mount the worm to the motor)1215D-9 motor (tiny, but powerful enough to easily drive a larger N-scale engine!)435-6 flywheel
And as I said before, I used Intermountain semi-scale freight car wheels (33"). Any 33" freight car wheels with a 3/32" metal axle and standard width needle-point bearings will work, but I like IM's best.
I'm not sure if I can give any great hints on how to build this chassis, except that I started with mounting the axles, constantly checked to make sure everything fit and worked smoothly in the fully assembled model, and did the center idler gear last to make mesh adjustments easier. It's all a process of taking things one step at a time, and avoiding short cuts!
Nice work, excellent job!!Thanks for sharing & the ideas!
Oh my...beautiful work there!!
Any argument carried far enough will end up in Semantics--Hartz's law of rhetoric Emerald. Leemer and Southern The route of the Sceptre Express Barry
I just started my blog site...more stuff to come...
http://modeltrainswithmusic.blogspot.ca/
Pretty neat, as usual!!
The whole design seems to be very simple, which of course is a sign of a good design!
I have the Mack kit. Any chance you could provide a list of part numbers and hints on how you built the drive?
I built this same kit probably 20 years ago, and powered it with ... Tenshodo power truck? I think that's what it was. Wasn't nearly as geared down, though, but it'd move maybe 3-4 cars. I managed to equip it with a pair of Kadee couplers. I'll see if I can find it and post a pic or two. It left the cab vacant in case I want to add a decoder, or an interior.
Brad
EMD - Every Model Different
ALCO - Always Leaking Coolant and Oil
CSX - Coal Spilling eXperts
Very cool! I always wondered what people did with this kit, other than make a load out of it or park it at the end of a weed-grown siding.
No decoder, though? You must be in DC, but it looks like one of the smallest could be shoe-horned in?
Mike Lehman
Urbana, IL
Sweet.
Dennis Blank Jr.
CEO,COO,CFO,CMO,Bossman,Slavedriver,Engineer,Trackforeman,Grunt. Birdsboro & Reading Railroad
Nice work, Darth!
Ed
This past Christmas, I was given a Mack 15-Ton critter kit from Wiseman Models. It's an unpowered, all metal HO scale kit with absolutely no room for any of the currently available drive systems (except possibly a modified Stanton drive). So, I made my own!
Everything just barely fits, but I managed to create a design that requires almost no modification of the metal body, and I even fit a small flywheel in there! The motor, flywheel, and gearing are all from NWSL, the wheels are Intermountain 33" semi-scales, the wipers are a Kadee centering spring, and the rest is made from K&S brass stock.
The motor is very tiny at only 10x12x15mm, but it's surprisingly powerful and runs smoothly and quietly, with very good low-speed torque, and it's also very power efficient and slower than most other tiny motors. The gears have a total ratio of 32:1, giving my Critter a very realistic speed range. And with the white metal body, it has very good traction for its size.
Now I just have to figure out how to mount the couplers at the proper height and paint the thing. And when I do, I'll definitely post more pictures.