Hello All,
wjstixI set up a circle of Kato track on a separate 4' by 4' flat shelf under one of the reverse loops. I can power it with a DC power pack...
For testing motors, I use a DC power pack. It's a basic Bachmann with a 1/8-inch mini plug track power output.
I cut the track connector end off the track power wires and added alligator clips so I can attach it directly to the contacts on the motor.
Hope this helps.
"Uhh...I didn’t know it was 'impossible' I just made it work...sorry"
I started with a Digitrax Zephyr, but switched to CVP eventually. I set up a circle of Kato track on a separate 4' by 4' flat shelf under one of the reverse loops. I can power it with a DC power pack, or with the Zephyr, like for testing or break-in runs. I also have a switch set up so I can use the track to program with the Zephyr.
Make sure you can replace the roller bearings. I have a set I believe are made by Bachman that have non replaceable bearings. I've lost 2 rollers on them. The other set has no name as to manufacturer and the bearings are easily replaced.
Just my thoughts.
Pete.
jjdamnit Hello All, JDVass Yes I do use rollers. I find that it is more convenient then (SIC) having the loco running around the track at full speed. I've been considering adding rollers to my test track set-up. Thank you for your response. Hope this helps.
JDVass Yes I do use rollers. I find that it is more convenient then (SIC) having the loco running around the track at full speed.
I've been considering adding rollers to my test track set-up.
Thank you for your response.
Rich
Alton Junction
JDVassYes I do use rollers. I find that it is more convenient then (SIC) having the loco running around the track at full speed.
I have a piece of HO flex track mounted on a 1 x 3 piece of maple left over from a project decades ago. It has a spare Power cab panel on one end and a plastic version of the KDee coupler height gauge on the other. I also have the USB interface for the Power Cab and my Lok programmer on a shelf that is used with it. My Lenovo netbook has all the software ready to go anytime. When the test track is not in use it hangs on the side of the little workbench. The rollers are a great addition. The test track has become an invaluable tool.
jjdamnit How do you break in the locos on that short track section? Do you use rollers?
How do you break in the locos on that short track section?
Do you use rollers?
Yes I do use rollers. I find that it is more convenient then having the loco running around the track at full speed.
Thank you for sharing!
My pike uses an NCE Power Cab wireless 5 Amp system.
I have a similar setup with a Digitrax PR3 running DecoderPro from my Mac to a standalone programming track.
Recently I purchased the ESU Decoder Tester but hadn't thought about linking it to my test track.
Great suggestion!
My question is...
JDVass...and break in locos right on the work bench (SIC).
Thank you for your response, and as always...
Well, I got a little bored today. Still waiting on a few parts for my steamers, so I can't finish those. So, I started digging around the shelves and found an old MRC Prodigy Express set up that I received from a friend who passed away. My layout is Digitrax now, but MRC was my first DCC system. They work well and are very user friendly. I then had an epiphany.
I took some old Kato unitrack, attached a female JST plug to it, and then glued it to a piece of 1x4. Then I attached male plugs to my PR3 programmer and the MRC system. I also attached a female plug to my decoder tester as well so it can plug into the MRC unit to test decoders. It works great. Now I can program, test, and break in locos right on the work bench. It was a good thing my wife didn't have any chores for me today. The locos on the track in the photo is just to hold the track down while the glue dries.