Travis N Scale An update - I've received and installed my PSX AR and things seem to be working perfectly. All in all I'm happy I went with the PSX AR for my reversing section over Digitrax.
An update - I've received and installed my PSX AR and things seem to be working perfectly.
All in all I'm happy I went with the PSX AR for my reversing section over Digitrax.
Rich
Alton Junction
Hi everyone
I was having some hesitation in a BLI locomotive pair but now it was happening well after the train cleared the reversing district. When I gave the track and wheels a good clean (they weren't very dirty) I got no improvement. I THINK the train was just too heavy as when I ran just the locomotive through, it hesitated much less.
The section of track has fewer feeders than others so tommorw I'll put in a couple pairs of feeders there. All my trains do slow down there - it's a steeper grade on a curve plus the lack of feeders might be causing a further drop in power.
I was careful to follow the directions and add the Digitrax jumper wire.
Travis N Scale I'm convinced that it is an issue of inrush current to the sound decoders on the BLI equipment. I've ordered a PSX AR to swap in place of the AR1 though I may end up having to replace the PM42 as well an replace that with PSX circuit breakers. Apparently the PSX AR does not operate well "downstream" of another circuit breaker. Hopefully the PSX AR solves the problem with the BLI equipment - they claim to.
I'm convinced that it is an issue of inrush current to the sound decoders on the BLI equipment.
I've ordered a PSX AR to swap in place of the AR1 though I may end up having to replace the PM42 as well an replace that with PSX circuit breakers. Apparently the PSX AR does not operate well "downstream" of another circuit breaker.
Hopefully the PSX AR solves the problem with the BLI equipment - they claim to.
The reason that a PSX-AR is not wired downstream from a circuit breaker is that the PSX-AR is not only an auto-reverser but also its own circuit breaker.
For years, I used Digitrax AR-1s to control the reversing sections on my layout with no problems. But, then I got the bright idea to divide my layout into power districts controlled by PSX units. That placed the AR-1s downstream from the PSX units, and conflicts began to immediately occur because the relay-based AR-1s could not react as fast to a short as the PSX units could. So, I had to replace the AR-1s with PSX-AR units which became their own power districts.
My feeling is that you will have to replace not only the AR-1s but also the PM42 since both are relay-based units.
Thanks Rich
Since my booster is 5amp, I'm thinking the default trip current (J6) should be fine and yes the J7 will have to have the jumper installed since I'm using a Digitrax booster.
Hi Greg
No the two non sound equipped Kato locomotives I have breeze through all 4 entrances and exits of that reversing district with no issues.
What about using a frog juicer, they make one that can be used as a reverser.
Travis N ScaleBLI has acknowledged that the inrush current to their sound decoder is an issue.
is there a problem with other, non-BLI sound locos?
greg - Philadelphia & Reading / Reading
Travis N Scale Thanks Rich BLI has acknowledged that the inrush current to their sound decoder is an issue. The PSX AR specifically claims to address this so here's hoping I have the same success you've experience. Yes the Digitrax PM42 and AR1 seem to have been made for a by gone era and haven't been updated for today's locomotive models which is a shame as I quite like the boosters and throttles though the instruction manuals are terrible.
BLI has acknowledged that the inrush current to their sound decoder is an issue.
The PSX AR specifically claims to address this so here's hoping I have the same success you've experience.
Yes the Digitrax PM42 and AR1 seem to have been made for a by gone era and haven't been updated for today's locomotive models which is a shame as I quite like the boosters and throttles though the instruction manuals are terrible.
Good luck and keep us posted.
Rich.
Two comments.
One, I have been running BLI Paragons through PSX-ARs for years and years without a burp. Inrush of current, phooey.
Two, Digitrax AR1 is a dinosaur. Running a mechanical relay in tandem with solid state circuit breakers simply doesn't work well.
No if that track is removed then there is no way to return back into the yard. I'm hoping that keeping just that red reversing section to the left side of the layout but putting it on the PSX AR solves this.
The fact that the Kato runs over all of these reversing sectio entrances and exits going in all directions flawlessly is pointing towards it being an issue with the BLI Locomotives and the slower relay switches on the Digitrax PM42 and AR1.
I have 10 BLI locomotives and all have behaved exactly the same way - even with only one locomotive being on the layout.
My 5 amp power supply is more than enough.
I do have a back up plan of rewiring and reworking that one large reversing district and dividing it into the two sidings on the left side of the layout being one reversing district and all 3 tracks on the right side of the layout each isolated as separate reversing sections.
Thats a pile of work so it's the last resort if the PSX AR fails to solve the issue.
Here is what the reworked layout would look. The track in green can remain wired as is. The track in red is the new reversing tracks. All track not highlighted must be rewired so that Rail A is toward the rear of the layout.
https://imgur.com/gallery/Kh3xsjY
https://imgur.com/gallery/V9dOK33
https://imgur.com/gallery/Tc3lilI
My kingdom for a picture.
Ok let me think about it.
Henry
COB Potomac & Northern
Shenandoah Valley
Again I appreciate everyone's advice, questions and patience while I tried to sort out how to post the pictures.
Another clarification before someone worries - my Walthers Switch Machine zone coming off of the PM42 ONLY powers the physical movement of the switch machines. The track power that the switch machine routes to the powered frog is being supplied by the local track bus.
Spoke with Tony's Trains regarding the possible use of the PSX AR as a possible remedy here.
They confirmed that the Broadway Limited Imports sound equipped locomotives are particularly sensitive to these reversing situation. The inrush of current to keep the sound decoder capacitor "charged up" gets misinterpreted as a short circuit. The PSX AR claims to solve this.
They did caution that if the PM42 is remaining then the PSX AR must be installed upstream of the PM42 off of the direct booster feeds. This prevents having two circuit breakers "arguing" with each other.
I hope that will solve it. If not then I will try replacing the PM42 with 3 PSX circuit breakers in addition to the PSX AR. At that point I may just have to rewire such that my reversing section has only 2 entrances/exits and there is a couple more reversing sections off to the right end of the layout.
Keep you all posted!
Oh and I am modelling the PRR and NYC railroads during the steam and diesel transition er.
Thanks for the replies everyone.
To clarify, I am modelling in N scale using Atlas flex track and Peco Electrofrog turnouts controlled (and frog powered) through Walthers Switch Machines.
I am using a Digitrax DCS210+ booster, 2 DT602 throttles and a Zephyr DCS52 set as a booster though it is not connected as a booster. It is only connected with a loconet cable and is being used as my yard throttle.
I have aPM42 dividing the layout into a yard, mainline, reversing district (the red track in the image) and the switch machine track power bus.
An update - yesterday I set the PM42 reversing zone back to non reversing and installed a Digitrax AR1 instead to handle the reversing. No luck - same result though interestingly enough, when I installed it I reversed the Rail A & B without realizing it.
This changed the location where I was observing the problem from Entrance (or exit) 1 and 3 counting down from the top of the imageof the reversing section to 2 and 4. Very weird.
Failing that, my next step will be to rewire a large portion of the layout such that rail A (red wire) is toward the back of the layout always and create separate reversing loops at each end of the layout.
Thanks for the replies everyone. Here are some image links. I will type a reply to some of your comments and questions as well as an update to some additional troubleshooting that I have tried.
https://imgur.com/gallery/t0xIe2p
https://imgur.com/gallery/Vw1qA9Z
Alright everyone, let's try this again with some pictures.
PR4 is actually 4 DPDT relays. As an autoreverser the relay for that reverse section will trip and reverse phase of the outputs as long as the wires are connected properly. Since thay are DPDT relays, there will always be a conection to one set of the relay's outputs even when power to the PR4 is off. When powered the PR4 will trip a relay to its opposit position if a short circuit is detected. When used as a circuit breaker, only one side of the relay is connected to the track. That is the side that is normally closed when the relay is not energized. This way there will always be track poewer to the section even if PR4's power supply is turned off.
Martin Myers
Argumentative posts have been deleted. Go to your corners, gentlemen. Answer the OP's question or don't post.
--Steven Otte, Model Railroader senior associate editorsotte@kalmbach.com
Travis N ScaleWhen zone 4 is ALREADY tripped (red light is on), I can travel through here from right to left with no issues BUT if I go through from left to right, the locomotive hesitates, then restarts on its own. The PM42 zone 4 light then switches off and everything goes along fine.
The PM42 zone 4 light then switches off and everything goes along fine.
can someone explain what the "red light" on and then off suggests?
why would the direction of travel make a difference?
looks like the PM42 Quad Power Unit is not purely an auto-reverser. what if two adjacent "districts" managed by the PM42 are both configured as revering sections?
Travis. I'm not a mind reader so will not pretend to know what you "obviously" meant. I will suggest you look at the thread in General Discussion regarding how to post a photo and try again. People are grasping at straws at the moment to try to help you out.
Mike
gregc continuity is a measurement of resistance. mention of polarity/phase is irrelevant and confusing. yes, the OP may be confusing continuity with polarity.
continuity is a measurement of resistance. mention of polarity/phase is irrelevant and confusing.
yes, the OP may be confusing continuity with polarity.
Lastspikemikewhile at the other end at the same time attempting to test for continuity would show a dead short due to reversal of polarity or phase as the case may be.
mike
not sure how your comment is "practical". continuity is a measurement of resistance. mention of polarity/phase is irrelevant and confusing.
Without a track plan, we are at a considerable disadvantage. But, in my experience in dealing with reversing section issues, testing for continuity is something that I have never had reason to do.
gregcseeing the same voltage when powered doesn't imply continuity. continuity means a zero ohm path. there's a bit of circuitry between the main and reverse section rails that result in a non-continuous connection. a test for continuity, or the lack of it across gaps should be done without anything (i.e. AR) connected to at least the reverse section rails
Well put Greg.
-Kevin
Living the dream.
I agree with Gregc on this...........
Take care!
Frank
gregc Lastspikemike Continuity isn't necessarily a surprise. At one end of a reversing section you should have continuity seeing the same voltage when powered doesn't imply continuity. continuity means a zero ohm path. there's a bit of circuitry between the main and reverse section rails that result in a non-continuous connection. a test for continuity, or the lack of it across gaps should be done without anything (i.e. AR) connected to at least the reverse section rails
Lastspikemike Continuity isn't necessarily a surprise. At one end of a reversing section you should have continuity
seeing the same voltage when powered doesn't imply continuity.
continuity means a zero ohm path. there's a bit of circuitry between the main and reverse section rails that result in a non-continuous connection.
a test for continuity, or the lack of it across gaps should be done without anything (i.e. AR) connected to at least the reverse section rails
LastspikemikeContinuity isn't necessarily a surprise. At one end of a reversing section you should have continuity
Travis N ScaleHere is a diagram of my reversing zone, it’s wiring and the results of continuity testing across the insulating gaps. I was kind of surprised there was any continuity? I assumed there would be none since it’s supposed to be electrically isolated? 2 of the 4 entrances/exits of the red reversing district had continuity in both rails and 2 had only one rail with continuity.
to the Model Railroader magazine discussion forums. We are very glad that you have found us. Your first few posts will be delayed by the Kalmbach Media moderators, but that ends soon enough, usually after just a few posts. Please stick around through the delay and become a permanent part of the discussions.
My first suggestion is to not use the term "continuity" for electrical troubleshooting, and never use a continuity tester to troubleshoot model railroad track.
Instead, use a digital volt/ohm meter (DVOM), sometimes called a multi-meter, as your troubleshooting tool. I am in love with the Fluke model 101 as a basic go-to-troubleshooting tool for model railroads, but there are less expensive options.
You need to know where you should see high and where there should be low resistance. Generally speaking, anything below 10 ohms can be considered a closed circuit, anything over 1,000,000 ohms can be considered open. In basic track circuits anything between 100 ohms and 10,000 ohms could be a problem and should be investigated.
This is why you need to learn what you should see. When you see 1.2 ohms where you would expect an open circuit, that is a problem.
Without seeing all the particulars of your layout, there is no advice I can offer directly.
Please stay around.
Can anyone make sense of this?
to the forum. You are stuck in moderation for a short while.
I tried to send you a pm and it's hopeless with 3 different browsers. I was going to volunteer to post you picture. It hasn't worked with Firefox for at least a year, but neither Chrome nor Edge would allow me to compose a message to you.
You can't simply attach a picture to your post, it has to be on the internet at a site like Imgur.com, not a site that requires a login like dropbox, google photos, facebook. There is a sticky in the General Forum on how to do that. Imgur is free. Once you have a photo there copy the "BBLink" directly as text into you post. Do not use the picture icon or the link icon.
Imagining a picture what we can't see makes it impossible to diagnose your problem.
I'm just fishing in the dark here, but some of the reversers have a setting for trip time. BLI locomotives are historically notorious for disliking even brief interruptions of their track feed, no matter why it happens. If it happens because your PM-42 is a little slow to reverse the phase, that may be just enough to cause your BLI decoder to balk.