The information I've been missing is the voltage use of the LED. I know that amperage in series stays constant; that is a strong argument for wiring the two LEDs of each number board in series if I decide to use two LEDs. 5 ma * 5 volts is .025W. And I have to experiment to see if one might work.And number boards are noticeable during the day, but just barely; they shouldn't be as bright as the headlights, which is a whole nother story. Just like the class lights are noticeable, but not all that bright.
Disclaimer: This post may contain humor, sarcasm, and/or flatulence.
Michael Mornard
Bringing the North Woods to South Dakota!
I think I misread your 400mA comment as how much current your LEDs are using.Just remember1: if you wire your LEDs in series, the voltage drop adds up. So two LEDs would be a 7V drop. Three would be a 10.5V drop which would be the practical limit. The advantage of doing it this way is your current stays the same and the power that the resistor has to disappate becomes way less because you have 5->1.5V left over after the drops.2: If you wire your LEDs in parallel, the current adds up. So two 10mA LEDs become 20mA. 3 would be 30mA, etc.It sounds like you'll have a nicely lit loco when you are done.
Don - Specializing in layout DC->DCC conversions
Modeling C&O transition era and steel industries There's Nothing Like Big Steam!
DigitalGriffin Formula is V*V/R. your input is roughly 12 volts. Your LED light takes roughly 3.5 volts away from that leaving you 8.5Volts. 15 ma = .015 ampsV = IR8.5 = .015R566 = Rso lets go with common values and pull a 560Ohm resistorV * V / R = Power8.5 * 8.5 / 560 = .129 WattsBarely an 1/8th watt. So a 1/4 watt resistor is fine. Those must be some LEDs to handle 400ma. that's 4/10th an amp. Most burn out over .020 amps. (20 ma)
Formula is V*V/R. your input is roughly 12 volts. Your LED light takes roughly 3.5 volts away from that leaving you 8.5Volts. 15 ma = .015 ampsV = IR8.5 = .015R566 = Rso lets go with common values and pull a 560Ohm resistorV * V / R = Power8.5 * 8.5 / 560 = .129 WattsBarely an 1/8th watt. So a 1/4 watt resistor is fine.
Those must be some LEDs to handle 400ma. that's 4/10th an amp. Most burn out over .020 amps. (20 ma)
I'm not sure where you got 400 ma from. Each LED is 10 mA, there are two LEDs per number board, four number boards, that's eight LEDs total.With a 1K resistor we're talking 10 mA. Actually, I should probably cut it down so the number boards aren't too bright. Say a 2K resistor for roughly 6 mA. Times eight is 48 mA, or .048A. Times 8.5 = .408 W, so a 1/2W resistor
The missing info was how much voltage the LED uses, thanks.
Bayfield Transfer Railway Thanks.The LEDs I have are SMT 0604s, which are pretty tiny. Also I've noticed that on a lot of diesels at least, you can tell where the lightbulbs are behind the numberboards on the prototype and I was hoping to duplicate that effect. But you're right about resistsors being tiny, even 1/4 w, and also very cheap. Just heatshrink over the whole thing and there's plenty of room in an Athearn HO body.
Thanks.The LEDs I have are SMT 0604s, which are pretty tiny. Also I've noticed that on a lot of diesels at least, you can tell where the lightbulbs are behind the numberboards on the prototype and I was hoping to duplicate that effect. But you're right about resistsors being tiny, even 1/4 w, and also very cheap. Just heatshrink over the whole thing and there's plenty of room in an Athearn HO body.
I'm beginning to realize that aging is not for wimps
Bayfield Transfer Railway Maybe this is a good place to get help.I want to connect my numberboard LEDs in parallel. This means I add the amperage. If I have 8 LEDs, 2 per numberboard, and each uses 10 mA, what wattage does the resistor need to be? W = V*A, and A= .010, but do I use 12 for V or some other value? If it's 12v, then even at .01A each I'm pushing nearly a watt, and I'd be better off using 8 1/4 watt resistors located near the numberboards rather than one resistor for all.It was my hope for convenience sake to have a bit of PC board in the engine shell with the resistors soldered on and then a plug soldered to that so that when removing the shell, one plug disconnects all the light circuits.
Maybe this is a good place to get help.I want to connect my numberboard LEDs in parallel. This means I add the amperage. If I have 8 LEDs, 2 per numberboard, and each uses 10 mA, what wattage does the resistor need to be? W = V*A, and A= .010, but do I use 12 for V or some other value?
If it's 12v, then even at .01A each I'm pushing nearly a watt, and I'd be better off using 8 1/4 watt resistors located near the numberboards rather than one resistor for all.It was my hope for convenience sake to have a bit of PC board in the engine shell with the resistors soldered on and then a plug soldered to that so that when removing the shell, one plug disconnects all the light circuits.
All I have used are 1k, 1/8 watt resistors. I have measured 9 ma many times with 20 ma LED's. No heat to worry about.
Decoder voltage was about 12.2 vdc.
Rich
If you ever fall over in public, pick yourself up and say “sorry it’s been a while since I inhabited a body.” And just walk away.
Always buy 1/4 watt resistors. They are about half the price of 1/8th watt resistors.
LION buys int in a box of 1000 for about $12.
ROAR
The Route of the Broadway Lion The Largest Subway Layout in North Dakota.
Here there be cats. LIONS with CAMERAS
Geromewith a regular little LED and a 1/8 watt resistor, the resistor became too hot to hold.
what size resistor? do you know the voltage drop across the LED?
greg - Philadelphia & Reading / Reading
If they are getting hot you are probably using too small a resistor value. White LEDs tend to be extremely bright and there's no real reason to use anything less than a 1K resistor. A 1K resistor results in less than 10ma, less than 1/10 of a watt, so a 1/8 watt resistor is fine and won't get too hot. With surface mount LEDs, and standard LEDs were there isn't a long light pipe between the LED and the front to attenuate some of the brightness, even 1K isn't enough. 1.5K, 2K, even 4.7K is not out of the question to get a pleasing light. As you go bigger on the resistor, the current decreases, thus decreasing the wattage and thus the heat generated.
Consider this - my resistor wheels for blocl detection have a 10K resistor in them. Every axle with a resistor is the same as taking a 10K resistor and putting it directly across the rails. At a nominal 15V across the rails, that's about 2/100 of a watt. They don;t even get warm - which is a good thing, since many are metal wheelsets with plastic axles.
--Randy
Modeling the Reading Railroad in the 1950's
Visit my web site at www.readingeastpenn.com for construction updates, DCC Info, and more.
The heat output of the resistor is the same independant of the wattage of the resistor, assuming they are the same ohmic value. It is a function of the dissipation of the power you are trying to loose. A 1000 ohm resistor gets rid of the same power no matter what the wattage rating. The bigger resistor feels cooler as there is more surface area to dissipate the heat, but the amount of heat generated is the same. The power used by the circuit depends upon the series resistance of the circuit not the current available from the source. This could get more complicated by figuring out the actual output of the sources and measure each with a RMS meter or oscope and use the RMS value of the voltage for comparison, but that is probably overkill. Your two power sources may not be as close as you think.
You must be careful not to melt the plastic shell of the locomotive, as that will happen before you burn out the resistor. Use a larger wattage resistor if there is room as it will spread the heat over a larger area. If the LED is bright enough you may be able to use a larger ohm value in series as that will decrease the current, thus the heat will be reduced.
Paul
Dayton and Mad River RR
Lots of LEDs run with 20mA. A 600Ohm resistor may use 12V with 20mA. That results in 0.24W. That is to much for an 1/8W resistore. Use a 1/4W resistor or a more gentle LED.
Most LED will do fine in series with a 1.500Ohm resistor. That drops the current and 1/8W resistors are fine. That is what I install in all my engines and it works fine.
Reinhard
Interesting question. I have experienced hot resistors in the past. They were 1/8 watt. Since then I have used 1/4 or 1/2 watt resistors but I have never tested the heat output from the higher watt resistors. Just lazy I guess.
Dave
I'm just a dude with a bad back having a lot of fun with model trains, and finally building a layout!
I never noticed before, but when I was testing some DC locos with a power pack putting out 13V @ 400mA DC with a regular little LED and a 1/8 watt resistor, the resistor became too hot to hold.
Now, since my Zephyr command station is capable of 12 V @ 2.5 amps, does that mean the resistors on the LEDs from the DCC decoders are also getting hot, or do the decoders reduce this heat significantly? I know the LEDs are better because they run cooler, but are the resistors getting hot? I never held one under power.
Thanks