Login
or
Register
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Home
»
Model Railroader
»
Forums
»
Layouts and layout building
»
Foam board advice
Foam board advice
638 views
5 replies
Order Ascending
Order Descending
Gary 740
Member since
December 2005
From: Lewis Center, Ohio
25 posts
Foam board advice
Posted by
Gary 740
on Friday, December 9, 2005 3:34 PM
I am building a new layout with 3" foam board. I would like advice on the best way to cut out space for rivers and roadways. I have seen "Woodland Scenics" hot wire and their foam cutter bow & guide, are these good tools for this kind of project? Any experienced advice would be appreciated on this subject.
Thanks,
Gary
Reply
selector
Member since
February 2005
From: Vancouver Island, BC
23,325 posts
Posted by
selector
on Friday, December 9, 2005 3:39 PM
They are good tools, but you really ought to use them outdoors. They will release toxic fumes by heating the foam.
Reply
Anonymous
Member since
April 2003
305,205 posts
Posted by
Anonymous
on Friday, December 9, 2005 4:35 PM
A knife works just as well. Make sure to have Sculptamold handy to fill in gaps and provide a finished surface.
Reply
Edit
Janafam
Member since
April 2001
From: New York State, US
110 posts
Posted by
Janafam
on Friday, December 9, 2005 6:04 PM
Hot wire is fast but the fumes are a concern you should be aware of. Knives of small saws work but you have more of a mess with the particles that break off and become static electricity gremlins.
Janafam
Reply
2021
Member since
January 2013
180 posts
Posted by
2021
on Friday, December 9, 2005 6:27 PM
One if the best tools for forming foam is the Sureform tools. These are like carse files and are available in any hardware store or home improvement store (e.g. Home Depot). Also buy some cheap bread knives at the Dollar Store. Whenever you use a sureform tool, have a vacuum cleaner handy.
Ron K.
Reply
dgwinup
Member since
May 2005
1,168 posts
Posted by
dgwinup
on Friday, December 9, 2005 9:16 PM
The best tool I found for carving foam indoors is those disposable hobby knives that have segmented blades. When the tip gets dull, you break off a segment, exposing a new tip. The whole blade is nearly 2" long when fully extended and has fair flexibility. If you bend it too far, it will snap off. If you have to bend it that far, you aren't using it right. Use the blade to cut successively smaller pieces of foam as you carve deeper into the foam.
Here is a link to one kind of knife with snap-off blades:
http://www.widgetsupply.com/page/WS/PROD/X-ACTO-utility/BEP26
I have found similar but cheaper disposable knives at the dollar stores.
I haven't used these items, but those long thin blades look like they would work well for carving foam:
http://www.polymerclayexpress.com/tools.html
Here is a photo of a Thomas-style layout I made for my grandson:
This clearly shows how the wooden tracks were inserted into channels that I carved into the foam. The channel is less than 2" wide. I cut straight down along the outer edge of the track, then, holding the blade at a sharp angle, I sliced a wedge-shaped section off of each side, leaving a center ridge. Then I progressively cut smaller pieces off the center ridge, using the flexibility of the blade to get the bottom of the channel smooth and flat.
For something as wide as a creek or river, cutting wedge-shaped sections out would be easy.
Hope this helps.
Darrell, quiet...for now
Darrell, quiet...for now
Reply
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Users Online
There are no community member online
Search the Community
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT
Model Railroader Newsletter
See all
Sign up for our FREE e-newsletter
and get model railroad news in your inbox!
Sign up