Login
or
Register
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Home
»
Model Railroader
»
Forums
»
Layouts and layout building
»
Transformer wiring
Transformer wiring
749 views
5 replies
Order Ascending
Order Descending
btdrum
Member since
September 2005
From: San Rafael, CA
7 posts
Transformer wiring
Posted by
btdrum
on Thursday, December 8, 2005 11:01 AM
I'm new to model railroading and have a transformer question. I have a Tech 2 Railmatser 2400 transformer and am curious about the hook ups. The 3 hook ups I have are: Variable DC, Accessories AC, and Fixed DC. I have Variable DC going to the rail, but where do I hook the switches up to, Fixed DC? Or do I have these reversed? Obviously lights and such go to Accessories AC. And on that note, how do I hook up more than 1 accessory? Any help on these subjects is greatly appreciated. It's nice to hear from experienced modelers!
Reply
lonewoof
Member since
April 2004
From: SC
318 posts
Posted by
lonewoof
on Thursday, December 8, 2005 12:15 PM
Are you asking about where to connect your track switch machines (that throw the switches)? They go to Fixed DC. Be sure to use momentary contact (electrical) switches, so power doesn't stay connected to the switch MACHINES constantly. (That will kill them).
You are correct in connecting Variable DC to the track.
Accessory AC goes to lights and such. You probably want each light run in parallel (2 wires from each, back to the Accessory terminals).
Remember: In South Carolina, North is southeast of Due West... HIOAg /Bill
Reply
Leon Silverman
Member since
July 2004
785 posts
Posted by
Leon Silverman
on Thursday, December 8, 2005 1:03 PM
Solenoid type switch machines will work on either AC or DC current. They can be connected to either your Fixed DC or AC. Either way, they require momentary contact swtiches to avoid being burnt out. The slow-motion, or geared type machines should be connected to the fixed DC terminals thru standard dpdt switches since they are intended to be powered up all the time. The fixed DC terminals can be used to power almost any accessory or lighting. If you run it through a reostat, you can control the speed of the accessory or brightness of the light..
Keep in mind that the total power draw between all three terminals cannot exceed the maximum power output of the transformer. Also, if you are powering solenoid type switch machines, run them through a capacitor discharge circuit or on a dedicated transformer by themselves. Otherwise, when you activate a switch, even though there is only a momentary power draw, running trains powered by that same power pack will also slow down momentarily, until you release the button. The speed drop will be noticeable, even from a larger power pack.
Reply
Anonymous
Member since
April 2003
305,205 posts
Posted by
Anonymous
on Thursday, December 8, 2005 1:27 PM
To add a little to what Leon said...
Although it's OK to start out using your transformer to power everything on a small layout, you should move to separate power supplies for all your accessories as soon as you start to add siginficant numbers of lights and switches. That way you don't take away from the transformers real purpose - powering your trains.
And it doesn't have to be expensive - just about everyone has some plug in electrical device that died, such as a drill, small appliance, etc. The "wall warts" that these ran off are usually in the 3- 12 V DC range, which is ideal for a variety of uses - lights, switch relays, etc. Simply cut off the plug they come with.
Or you can pick up an old Tyco or Atlas low-tech transformer at a train show for a few bucks and use it for your accessories.
In other words, save the High-Tech transformer for your trains. Lights and switches can run off the cheap, simple stuff.
Mike Tennent
Reply
Edit
btdrum
Member since
September 2005
From: San Rafael, CA
7 posts
Posted by
btdrum
on Thursday, December 8, 2005 3:39 PM
Thanks guys, that's exactly the kind of help I was looking for!
Reply
BR60103
Member since
January 2001
From: Guelph, Ont.
1,476 posts
Posted by
BR60103
on Thursday, December 8, 2005 9:30 PM
For hooking up more than one accessory, you should buy some terminal strips or barrier strips which are really just a long line of screws. The barrier strips have double screws so you can join the one set of terminals together and wire the accessories to the other side.
Any accessory that doesn't have a motor in it can probably be hooked to either the fixed DC or the AC terminals.
--David
Reply
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Users Online
York1
starcraftguy1
see all »
Search the Community
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT
Model Railroader Newsletter
See all
Sign up for our FREE e-newsletter
and get model railroad news in your inbox!
Sign up