Same location of the electric company team track, different view of the rusty chainlink fence.
SHane
A pessimist sees a dark tunnel
An optimist sees the light at the end of the tunnel
A realist sees a frieght train
An engineer sees three idiots standing on the tracks stairing blankly in space
I've made a ton of chain-link fences. Here's the guide I used:
https://www.youtube.com/watch?v=0_guMOYoCpw
Here's what I did:
Got picture frame hanging wire and cut a about a 3-6' section. Attach on end with a clamp to something and the other end in a drill chuck. I then use the drill to make the wire straight.
I next cut the wire into 12-18" sections and made a template using a scrap 2' section of a 1x3. That helped me figure out where to lay the frame, which I secured using a soldeirng iron and resin.
The fence itself I made using tulle (get at a craft store) in gray that I glued on using crazy glue with brush applicator.
The video I included makes far more sense than what I described.
Wasnt there an article in MR recently about making fence?
And of course cue video of chain link made by Luke Towan.
Shane
That is excellent-looking fence you made, Hornblower! I'm impressed.
York1 John
I have achieved excellent results using a hybrid fence based on the Walthers chain link fence kit. I have several scenes on my layout that required several 1:1 feet of fencing so I needed a way to make long fence sections quickly and easily. The trick was using 3' lengths of .020" music wire for the horizontal tubes between the fence uprights. The first thing to do after opening the Walthers fence kit is to carefully drill .020" holes through the side of the top and bottom sleeves (short thicker sections) on each plastic fence upright WHILE THEY ARE STILL ON THE SPRUE! Keeping the uprights on the sprue helps you hold them still much more securely during the drilling process. I also found it was much cheaper to cut a few short lengths of .020" music wire with each cut at a sharp angle to make cheap and much more forgiving drill bits. Do use a pin vise though!
Once all of the holes are drilled, remove the uprights from the sprues and perform any necessary clean-up (there is some flash). Next, choose an upright spacing distance and mark the upright locations on two lengths of music wire. Slide each upright onto the two lengths of music wire, then move it to a marked position. Repeat this until you have the desired length of fencing. Lay the fence frame on a flat surface and make sure the uprights are perpendicular to the music wire. Place a small drop of CA at each junction.
The hardest part of the job is accurately cutting the toule! Use a dark colored cutting mat or lightly spray the toule black and use a light colored mat. I have to use a magnifying visor to see the individual diamonds of the toule material. However, this makes it far easier to make cuts along a single row of diamonds. Toule is usually too stretchy to try to make a straight cut using a straight edge and hobby knife. I go along the material and cut each individual strand along one row of diamonds. It takes longer but your fence will look so much better.
With the toule cut, I find that I like to use pressure sensitive glue (PSA) to attach the toule to the frame. Apply a thin coat of PSA to one side of the fence frame, and once dry to tacky, press the toule into the PSA. Since the PSA is already partially dried and no longer flows, it cannot fill in the toule diamonds the way wet glues can. If you find spots that won't stick, add a very small drop of CA.
Paint the fence using either flat gray primer for an older fence or an aluminum color for a new fence. Weather as desired.
Although I used thread because I hadn't yet discovered EZ Line, EZ Line would be a far better choice to use for the barbed wire runs along the top of the fence.
The following pictures show different fence runs on my layout.
Hornblower
Hudson,
I found this video of what seems like a cheap and easy way to make realistic chain link fence:
https://www.youtube.com/watch?v=_vywJ4YPsYA
Note: I haven't done this myself, so I'm going strictly by watching the video.
Best I have seen is micron art.
Chain link would be good
If you mean chain link, then say so. But you may be thinking of something else
Henry
COB Potomac & Northern
Shenandoah Valley
I would like some tips about building ho scale industrial fencing. I vaguely remember a past article concerning fencin, but I can't seem to find it.
The fence wil surroun an electric power substatio.