Trains.com

Aristo radius 6 switches

7193 views
35 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    November 2005
  • From: Blackpool, Lancashire, UK
  • 448 posts
Aristo radius 6 switches
Posted by kimbrit on Monday, January 15, 2007 2:10 AM

Had a visit yesterday to a new - for me - model shop on Carnforth Station, of Brief Encounter fame with Trevor Howard and Celia Johnson (1946). Marvellous shop with lots of goodies, the reason for the vist was afore mentioned switches, never seen one before, and I have to say, WOW!! They look fantastic, but what a size, they will eat up a lot of room on my set up. Are they as good as I have been told? They look like they should be with the proper rail built frog. I didn't buy one but I came away with a Piko ready built water tower for £29, bargain!

Cheers,

Kim

  • Member since
    July 2003
  • From: Nebraska City, NE
  • 1,223 posts
Posted by Marty Cozad on Monday, January 15, 2007 8:13 AM

Kim

 Even on smaller RRs they are good for cross overs and parking sidings on your mainline.

You don't need them everywhere. Trains go through them very well. 

Is it REAL? or Just 1:29 scale?

Long live Outdoor Model Railroading.

  • Member since
    November 2005
  • From: Blackpool, Lancashire, UK
  • 448 posts
Posted by kimbrit on Monday, January 15, 2007 1:20 PM

Thanks for that Marty, as you say they wil be on the main line with my smaller switches serving the sidings.

Cheers,

Kim

  • Member since
    July 2003
  • From: US
  • 1,386 posts
Posted by Curmudgeon on Monday, January 15, 2007 3:10 PM

I use #6's on mainlines, and pasing sidings, even diverging route turnouts.

Everything else is a #4.

But, not 332.

 

Wait until you see a #8 double-curved turnout.....

  • Member since
    July 2003
  • From: Nebraska City, NE
  • 1,223 posts
Posted by Marty Cozad on Monday, January 15, 2007 4:59 PM
I run 332 rail because its cheaper and I don't run little girly engines.  heheheheheheh

Is it REAL? or Just 1:29 scale?

Long live Outdoor Model Railroading.

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Monday, January 15, 2007 5:06 PM
Can I get some pictures from the ole wise ones here?!
  • Member since
    January 2005
  • From: Slower Lower Delaware
  • 1,266 posts
Posted by Capt Bob Johnson on Monday, January 15, 2007 6:19 PM

Kim, one must bear in mind that they are NOT radius switches, they are #6 divergent switches!   They diverge from the straight at a 9.5 degree angle.    Unlike LGBs they cannot replace a curve section in a circle!

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Monday, January 15, 2007 8:53 PM
Not to hijack Kim's thread, but what's the difference between Aristo's #6 Turnout and the Wide Radius Turnout?  The catalog doesn't show the wide one.
  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Monday, January 15, 2007 9:12 PM

 Eric Cooper wrote:
Not to hijack Kim's thread, but what's the difference between Aristo's #6 Turnout and the Wide Radius Turnout?  The catalog doesn't show the wide one.

 

Eric,

Our techie says: 

The wide radius turnout will fit into a 5ft radius circle i.e. the diverging route is a segment of a circle.

The #6 turnout follows proper conventions that the railroads use i.e. it diverges 1 unit side ways per 6 units in length.

Projecting the frog intersection of the wide turnout results in approx. a #4 turnout.

 

Hope that helps

 

ER 

 

  • Member since
    September 2003
  • From: Centennial, CO
  • 1,192 posts
Posted by kstrong on Tuesday, January 16, 2007 9:44 AM
For more on switches, see this month's "Garden Railways Basics" column. Smile [:)]

Later,

K
  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Tuesday, January 16, 2007 9:30 PM
Got it.  Thanks, guys.
  • Member since
    December 2006
  • From: Michigan City, In.
  • 781 posts
Posted by spikejones52002 on Wednesday, January 17, 2007 6:03 AM

Thank You Elisabeth Reymond.

You are the first person to give me anything close to an intelligent explanation for a turnout number.

Everyone else I questioned, would look at me like I should know exactly what is Small, Medium, and Large.

Next I need to find out now they measure a curve by degree.

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Wednesday, January 17, 2007 9:06 AM
 spikejones52002 wrote:

Thank You Elisabeth Reymond.

You are the first person to give me anything close to an intelligent explanation for a turnout number.

Everyone else I questioned, would look at me like I should know exactly what is Small, Medium, and Large.

Next I need to find out now they measure a curve by degree.

 

Hello again,

Here's what our techie has in his library: 

Refers to curvature degrees used by the railroads

 

They use a 100ft "cord" as the standard, lay that cord inside the radius of a curve. Run two tangents from where the end points of the cord are on the radius to the center point of the radius. The included angle between the tangents is the degree of curvature for that radius.

 

Hope that helps

 

ER 

 

  • Member since
    July 2006
  • From: Pisa, IT
  • 1,474 posts
Posted by RR Redneck on Wednesday, January 17, 2007 9:30 AM

 Marty Cozad wrote:
I run 332 rail because its cheaper and I don't run little girly engines.  heheheheheheh

You got that right. That is why I run with Code 332 rail.

Lionel collector, stuck in an N scaler's modelling space.

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Wednesday, January 17, 2007 3:12 PM

Another way of looking at the railroad's 'degree of curvature' and how it's defined.

In Geometry, a chord is a straight line connecting two points on a circle.  A chord that passes through the center of a circle is the diameter.

The degree of curvature on the railroad is the answer to the question. ‘How many degrees does a 100 foot chord subtend?'.  In layman's talk, if you extend lines from the ends of the chord to the center of the circle, what is the angle between the two lines.  (In geometry talk, these extended lines are perpendicular to lines of tangency to the arc at the ends of the chord.)

Example 1: the degree of curvature is 1 degree.  The track therefore curved but one degree during the approximately 100 foot length of track.  It would take 360 sections of track, then, to complete a circle because there are 360 degrees in a circle.  The length of track for that circle would be 360 times 100 feet or 36,000 feet.  Dividing 36,000 feet by pi (3.14159) gives the diameter or 11,443 feet.  Half the diameter is the radius: 5,722 feet(all numbers rounded to the nearest foot).

Example 2: the degree of curvature is 3 degrees.  The track has curved 3 degrees during the approximately 100 foot length of track. Again, it would take 120 sections of track to complete a circle as 360 degrees divided by 3 equals 120.   A circle with a circumference of 12,000 feet has a diameter of 3,814 feet and a radius of 1,907 feet.

Note that these calculations are approximations as a chord is always slightly shorter than the arc it subtends.  But for angles less than 5 degrees, the two lengths are equal for all practical purposes.  As an example of how great the difference can get, a 60 degree curve would have a radius of 100 feet but the circumference of that circle iwould be 629 feet, the chord is still 100 feet, but the arc it subtends is 629 feet divided by 6 or 105 feet rounded to the nearest foot

Art

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Wednesday, January 17, 2007 5:56 PM

Follow up:

Even easier is a drawing Wink [;)]

 

 

Looking at the drawing data it would appear that using a 100ft Cord and the resulting calculated angle is somewhat more complicated than stating the radius - be it in Imperial or Metric measures.

What is the origin of the method??

 

ER 

 

 

 

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Wednesday, January 17, 2007 9:36 PM

Railroads cannot use a trammel and circle center to lay out an arc or a curved section of track.  Rivers, mountains, hills prevent this. But a table can be prepared to use a simple method of using a straight line and measuring offsets from this straight line.  The table has offsets for the various curvatures that are required.

Some 60 years ago while in high school, I came across a book that described this method.

1. At the start of the curve, Point A, extend a line 100 feet to Point B.

2. Consult the table for the offset needed for the desired curvature; at Point B, measure the offset at right angles from the line and establish Point C.

3. Sight a straight line from Point A to Point C and extend the line 100 feet to Point D.

4. At Point D, using the same offset from step 2, establish Point E.

5. As in step 3, sight a straight line from Point C to Point E and extend the line another 100 feet to establish another point.

This process is continued until the straight line is headed in the proper direction (called a tangent) that can be extended to the start of the next curve.

Flags are positioned at points, A, C, E, etc., and the track crew grades the right-of-way accordingly.

The table that I found had offsets specified for the mid points of the extended lines but I doubt that they were really necessary although they would define the curve more accurately.

Art 

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Thursday, January 18, 2007 12:19 AM
 artschlosser wrote:

Railroads cannot use a trammel and circle center to lay out an arc or a curved section of track.  Rivers, mountains, hills prevent this. But a table can be prepared to use a simple method of using a straight line and measuring offsets from this straight line.  The table has offsets for the various curvatures that are required.

Some 60 years ago while in high school, I came across a book that described this method.

1. At the start of the curve, Point A, extend a line 100 feet to Point B.

2. Consult the table for the offset needed for the desired curvature; at Point B, measure the offset at right angles from the line and establish Point C.

3. Sight a straight line from Point A to Point C and extend the line 100 feet to Point D.

4. At Point D, using the same offset from step 2, establish Point E.

5. As in step 3, sight a straight line from Point C to Point E and extend the line another 100 feet to establish another point.

This process is continued until the straight line is headed in the proper direction (called a tangent) that can be extended to the start of the next curve.

Flags are positioned at points, A, C, E, etc., and the track crew grades the right-of-way accordingly.

The table that I found had offsets specified for the mid points of the extended lines but I doubt that they were really necessary although they would define the curve more accurately.

Art 

 

Hello Art,

 

That is interesting. 

Interesting enough for our techie to check how other railways do it. 

We have a book from the RhB (Rhaetian Railways) which is strictly technical info on aspects of track geometry, various tables and formula.

The RhB uses 3 different "Cords" (10m; 15m; 20m), in addition to the main offset (1/2 "Cord") they also state the offset at 1/4 "Cord". Interestingly no mention is made of curvature expressed in degrees.  OTOH 100ft converts to 30.48m, which poses the question: was a smaller "Cord" used for designing and laying out NG railways with tighter curves?

Interesting!

 

ER 

 

PS RhB uses the 1:x for turnout angles. Wink [;)] 

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Thursday, January 18, 2007 9:04 AM

ER, it's not surprising that degrees of curvature are not mentioned in an European book as it's strictly American, based on that 100 foot chord.  Doesn't translate well into metric. 

Don't know about Canada, but a cord in my dictionary is something flexible like a cable or a heavy string, and a chord is a straight line between points on a circle or three or more musical tones,  triads, dominant sevenths. etc.

Your drawing of degree of curvature was neat!  Wish I could master posting pictures, etc.

Art

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Thursday, January 18, 2007 10:01 AM

Art,

 

Same dictionary up here, that "h" makes all the difference.

Could have been too much wood on someone's mind. Wink [;)]

 

ER 

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Thursday, January 18, 2007 11:08 AM

What's really neat about the 'chord' system is that easements are so easy to create.  For the first 100 feet, use the offset for a 1 degree curve, the next 100 feet - use the 2 degree offset, getting progressively tighter until the limit is reached as specified by the surveyor;  of course coming out of the curve the procedure would be reversed. 

Naturally, one could start the easement with something wider than a 1 degree of curvature, 1/2 or 1/4 no doubt, being used on high speed lines.

If the tables provide offsets for 1/4 and 1/2 chords, the narrow gauge lines could have just employed a 50 foot chord, using the 1/2 chord offset. 

Art

  • Member since
    March 2002
  • From: Norton, MA
  • 394 posts
Posted by piercedan on Friday, January 19, 2007 6:57 AM
Go t
  • Member since
    November 2005
  • From: Blackpool, Lancashire, UK
  • 448 posts
Posted by kimbrit on Friday, January 19, 2007 3:37 PM

Thanks for all this guys, I take it the switches work ok then, strikes the right chord so to speak!!

Cheers,

KimWink [;)]

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Friday, January 19, 2007 5:11 PM

GROANNNNN.  But I really, really DO like puns!!!

Art

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Friday, January 19, 2007 6:24 PM

To get this thread back on topic, the angle that a Number 6 switch makes is germane.

A Number 6 switch is defined as a spread of 1 unit in 6 units of length.  Thus to construct such a switch, measure six units from the frog point along one rail, measure 6 units along the other rail, and spread them apart one unit.  This measurement should include the width of both rails. 

In geometry, what we have here is an isosceles triangle, a base of 1 and two equal sides of 6.  Trigonometry is used to figure angles from linear measurements of right triangles.   Cutting an isosceles triangle down the middle creates two right triangles.  Dividing ½ by 6 yields 0.8333; this is the sine of a 4.78 degree angle.  Multiply by 2 to get the full angle of 9.56 degrees.

Now in real life, if the distance from the points to the frog was 100 feet, this switch would be a 9.56 degree curvature in railroad lingo.  In 22.5 scale, 100 feet scales down to 53 and a 1/3 inches.  The length of an Aristocraft Nbr. 6 switch is a figure I don't have.

The angles for other commonly used switches.

Nbr 4: 14.36 degrees

Nbr 8:   7.17 degrees

And the frog of an R1 LGB switch?  The entire switch is 300 mm long and curves 30 degrees. The distance from the points to the frog is about 239 mm, and using the diameter of the outer rail for computation yields an answer of 22.58 degrees.   Mighty sharp. 

Art 

  • Member since
    November 2005
  • From: Blackpool, Lancashire, UK
  • 448 posts
Posted by kimbrit on Sunday, January 21, 2007 10:52 AM
Whilst all of this has been really interesting I have just got back from Bay Models where I bought an LGB radius 5 switch, very nice too!
  • Member since
    February 2005
  • 1,821 posts
Posted by underworld on Sunday, January 21, 2007 11:26 AM

WoW! I never knew that much about the geometry of switch points! This will come in handy figuring out difficult areas on the layout I'm designing.

 

 

underworldBig Smile [:D]Big Smile [:D]Big Smile [:D]Big Smile [:D]Big Smile [:D]

currently on Tour with Sleeper Cell myspace.com/sleepercellrock Sleeper Cell is @ Checkers in Bowling Green Ohio 12/31/2009 come on out to the party!!! we will be shooting more video for MTVs The Making of a Metal Band
  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Sunday, January 21, 2007 8:55 PM

 artschlosser wrote:

 

.................................

And the frog of an R1 LGB switch?  The entire switch is 300 mm long and curves 30 degrees. The distance from the points to the frog is about 239 mm, and using the diameter of the outer rail for computation yields an answer of 22.58 degrees.   Mighty sharp. 

Art 

 

To be precise the frog angle at point of intersect is

21.919º for the R1 (600mm)

15.757º for the R3 (1175mm)

11.249º for the R5 (2320mm) 

 

ER 

 

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Monday, January 22, 2007 8:13 AM

E.R.. don't wish to nit-pick but when I measured the distance from frog to points, I effectively was measuring back from the end of the curve which is not easy to do accurately.  But since the points start a bit away from the end of the switch, I would expect the precise angle to be greater than what I calculated from the distance I measured; i.e., how far along the curve did the frog lie.

Are the figures you posted from calculations from physical measurements or from LGB data?

 Art 

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Monday, January 22, 2007 11:03 AM
 artschlosser wrote:

E.R.. don't wish to nit-pick but when I measured the distance from frog to points, I effectively was measuring back from the end of the curve which is not easy to do accurately.  But since the points start a bit away from the end of the switch, I would expect the precise angle to be greater than what I calculated from the distance I measured; i.e., how far along the curve did the frog lie.

Are the figures you posted from calculations from physical measurements or from LGB data?

 Art 

 

Art,

Our techie says: 

The posted results are the theoretical ones generated in a CAD program using the known values of the respective dimensions i.e. duplicate/offset the centerline of both the rad and the straight by 22.500mm; extend a tangent from the intersect point of the offset lineof the rad. That line corresponds to the frog angle.

 

Cheers

 

ER 

Search the Community

FREE EMAIL NEWSLETTER

Get the Garden Railways newsletter delivered to your inbox twice a month

By signing up you may also receive occasional reader surveys and special offers from Garden Railways magazine. Please view our privacy policy