Trains.com

anchoring track

1852 views
6 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    September 2007
  • From: Southwest, Idaho
  • 17 posts
anchoring track
Posted by idahocookie on Monday, April 21, 2008 7:38 PM

first time with a g scale layout and i am wondering if anyone can tell me if and how you anchor track for outside track.

 

thanks in advance  

Keep the rails warm
  • Member since
    December 2007
  • From: NJ (Kittatinny Mountains)
  • 436 posts
Posted by SNOWSHOE on Monday, April 21, 2008 7:56 PM

A lot of it depends on where you live.  For me I dug a 5-6 inch trench and then filled it with crusher fines (also known as stone dust and quarry wast).  This is used as your balast. Like the real RR.  I put this down in the trench and then packed it down real good.  then I wet it to harden it.  It makes it hard enought to support the track but you can break it up easily.  Then I lay the track down and add more stone dust to fill in the gap.  Dont forget to level the track as you go.  You can also add decrative balast as well on top. Go into the Graden Railroad main page.  You will find a wealth of info.  here is a link on balasting.  There are many other ways to support track.  But if you live in a cold climate dont anchor the track down.  http://www.trains.com/grw/default.aspx?c=a&id=55

 

Also there are great people on this forum who will give you great advise.

  • Member since
    July 2006
  • From: Shire Counties UK
  • 712 posts
Posted by two tone on Tuesday, April 22, 2008 1:07 PM

Hi idahocookie,Sign - Welcome [#welcome] I live across the pond my layout is on thermo lite blocksI use 4mm chippings for ballast. this is satisfactory over here the one advantage of no fixing the track down is I can change it with out to much hassle. I use LGB track with fish plates, i`ve changed my layput afew times and have had no problems with circuit breaks.

        Thermo blocks are very light and can be cut with a standard saw

                       Hope this helpsSmile [:)]

                Age is only a state of mind, keep the mind active and enjoy life

  • Member since
    August 2003
  • 6,434 posts
Posted by FJ and G on Tuesday, April 22, 2008 1:21 PM

I anchor my track down using 2 methods (about equally).

 

1. Embed the ties halfway in cement (ensure the cement is 4" thick and reinforced); you can add crusher fines on the cement while it is still wet for "ballast" look

2. Below the ties, nail battons (long strips of wood). These will go below the ballast and allow you to walk on the track without it shifting

 

hope this helps 

  • Member since
    February 2004
  • From: North, San Diego Co., CA
  • 3,092 posts
Posted by ttrigg on Tuesday, April 22, 2008 7:29 PM

I use one of the more common techniques. Almost just like the guys in 12 inch to the foot scale. I dig out a trench 3~4 inches deep and about twice as wide as the track. Lay down some weed cloth. Pour in some crusher fines. (The weed cloth will keep the crusher fines from sinking out of the roadbed into the mud.) Bring the rocks to slightly above ground level. Lay the track then ballast the ties with more crusher fines. I get crusher fines with a polymer adhesive mixed in. Helps control the ballast from drifting away. Very easy to break down to relocate a section of track when I need to, yet strong enough to walk on, I even slide 5 gallon buckets full of stone around on the track when reworking the mountain or other places where I (the wife) decides that I need more rock. The polymer makes the crusher fines reusable. Just crumble it up, put it back down and wet it. Cement/concrete like David does is a tad bit harder to change. Although he has started (or at least given directions) on building "sectional foundations/roadbeds."

Tom Trigg

  • Member since
    January 2005
  • From: Near Akron Ohio
  • 163 posts
Posted by mgilger on Tuesday, April 22, 2008 8:35 PM

Just let it float on top of your Balast like the real guys do. For my layout I have about 1/2 of it on balast layed using the trech method. On the other half, I did not dig the trench and just layed my balast on a weed barrier on top of the ground. I have not seen any difference between the two methods here in Northern Ohio.

 Regards,

Mark

 

M. Gilger - President and Chief Engineer MM&G web

Web Site: http://mmg-garden-rr.webs.com/

  • Member since
    October 2006
  • From: silver spring, md
  • 1,232 posts
Posted by altterrain on Thursday, April 24, 2008 9:37 AM

A good reason not to anchor your track to tightly -

http://www.largescalecentral.com/LSCForums/viewtopic.php?id=8801

-Brian 

President of

Search the Community

FREE EMAIL NEWSLETTER

Get the Garden Railways newsletter delivered to your inbox twice a month

By signing up you may also receive occasional reader surveys and special offers from Garden Railways magazine. Please view our privacy policy