Trains.com

I was thinking about getting the mth z-750 remote system good or bad?

724 views
6 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    January 2006
  • From: upstate NY
  • 110 posts
I was thinking about getting the mth z-750 remote system good or bad?
Posted by Locomotive681 on Friday, February 10, 2006 8:44 AM
Just want to know if its worth purchesing?[;)]
The route of the NYSW
  • Member since
    July 2003
  • From: North Texas
  • 5,707 posts
Posted by wrmcclellan on Friday, February 10, 2006 9:26 AM
loco681,

Which unit are you thinking about? The infrared (IR) remote (which is no longer shown in the MTH catalogs). It works fine. This unit uses an IR receiver built into the track power/terminal lock-on connector.

Regards,
Roy

Regards, Roy

  • Member since
    August 2003
  • 6,434 posts
Posted by FJ and G on Friday, February 10, 2006 11:11 AM
I use the Z750 with the DCS (used to use the starter set zapper). Both work well, tho DCS has greater range.

I've considered using the Z4000 or ZW but can't spring for it at this time and now I don't see any reason at all for changing my power needs as I have 2 Z750s and 1 Z500 from 3 starter sets; so why in heck do I need any more power than that (also have a Lionel DC brick which runs their 1999 cheapy construction set [:D]
  • Member since
    July 2002
  • From: DC
  • 203 posts
Posted by martinden on Friday, February 10, 2006 4:04 PM
I'm curious about just how directional the MTH (basic) IR remotes are. (I've gathered that there are no "channels" -- all remotes and receivers operate on exactly the same "frequencies," or whatever.) So, if you had two ovals (concentric double track) going around a living room, each with its own receiver/terminal lockon, perhaps 15 feet apart from each other, can you control the two trains independently by pointing the remote at one receiver or the other?
  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Friday, February 10, 2006 4:13 PM
"can you control the two trains independently by pointing the remote at one receiver or the other?"

The transmitter/receiver pair are as omnidirectional as possible to allow maxiumum liklihood of picking up a signal.
  • Member since
    December 2003
  • From: Central PA
  • 2,536 posts
Posted by jefelectric on Friday, February 10, 2006 6:50 PM
A local dealer told me that the reason they are no longer in the catalog is that they don't hold up. I have to agree, mine died a few weeks after I gave it to my grandson.

John
John Fullerton Home of the BUBB&A  http://www.jeanandjohn.net/trains.html
  • Member since
    December 2004
  • From: Southwest of Houston. TX
  • 1,082 posts
Posted by jimhaleyscomet on Friday, February 10, 2006 7:48 PM
They are directional enough to run two loops. Just put one reciever on each end and stand in the middle. You could also use your hand to block the signal or a convienent post, house or whatever. They are a tad slow to respond but do work well. They can fail but you can usually easily pick up another on Ebay.

They are perfect for the kids who want to run conventional but remote control (think Christmas layout without all the extra DCS equipment). And if you use Thomas or Beeps or some other slow switcher they will not run off the track when the kids go full speed.

Jim H

Join our Community!

Our community is FREE to join. To participate you must either login or register for an account.

Search the Community

FREE EMAIL NEWSLETTER

Get the Classic Toy Trains newsletter delivered to your inbox twice a month