Trains.com

Handlaying code 148 turnout (pictures)

1424 views
6 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    October 2004
  • From: 15 mi east of Cleveland
  • 2,072 posts
Posted by 1688torpedo on Monday, December 5, 2005 10:16 PM
Nice Work Dave! Boy Oh Boy! BB the Beagle sure is very good at building layouts now. You taught her very well. I'll bet the next thing you'll teach her to do is to build a Grits and Sweet Tea Warehouse complete with loading Dock & Tracks.[:)][;)][:P] Nice job though. Your layout is a work of art.
Keith Woodworth........Seat Belts save lives,Please drive safely.
  • Member since
    August 2003
  • 6,434 posts
Posted by FJ and G on Monday, December 5, 2005 12:49 PM
Thx, Bruce

Bob,

I did purchase some expensive n/s staples but was advised by garden RRers on 2 forums that the rust will hold the spike in place better (give it "bite") once it rusts. We'll see how many years it takes for the staple heads to rust off.

I have done an experiment of sorts. I've visited numerous wooden telephone poles throughout the area where campaign and how to lose weight posters have been stapled over the years. The staples they use are geenerally thinner than the heavy-duty ones I use and they inddeed were rusty but still holding fast very nicely and very difficult to extract.

A nice longitudinal experiment for me but I'm sure not for the authorities.

As well, trestle builders in garden RRs normally use steel brads that are very very small. You can see the rust marks after a period of time; but after 20-30 years; these are holding up nicely on various layouts.

As matter of fact, stainless steel spikes are made for largescale RRers and some G-scale guys have complained that over time, these rust-proof spikes have worked loose. I was skeptical at first about leaving things that rust outdoors until speaking w/numerous garden RRers.
  • Member since
    December 2001
  • From: Austin, TX
  • 10,096 posts
Posted by lionelsoni on Monday, December 5, 2005 12:44 PM
David, I'm surprised you're using your customary staples for spikes. Aren't they steel; and won't they rust? Or do you have stainless or non-ferrous ones?

Bob Nelson

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Monday, December 5, 2005 12:11 PM
Looks Great, David! Save installing the third rail and go electric with overhead cantary. Don't wanna stink up the inside of that warehouse with coal and deisel fumes[;)]
Seriously...well done! Gotta be impressed with anyone willing to tackle hand laid turnouts.

Bruce Webster
  • Member since
    August 2003
  • 6,434 posts
Posted by FJ and G on Monday, December 5, 2005 10:59 AM
Thanks, Doug.

I'll continue showing the progress for the few that like this particular aspect of toy trains.

It's scale rail actually, but too small to show up close w/my cheapy camera.

It's small looking compared to the usual toy train rail; but actually is mainline O scale rail. The toy train flanges clear the spikes; but just barely. Obviously, I'll be adding the 3rd rail.
  • Member since
    July 2003
  • From: Crystal Lake, IL
  • 8,059 posts
Posted by cnw1995 on Monday, December 5, 2005 10:35 AM
Wow, exquisite work, David. I am enjoying following your progress. From a distance, the rail looks like 'strap rail' that seemed to be much used by some 2-rail O trolley hobbyists -- anyone interested can see layouts with it at http://interurbans.net

Doug Murphy 'We few, we happy few, we band of brothers...' Henry V.

  • Member since
    August 2003
  • 6,434 posts
Handlaying code 148 turnout (pictures)
Posted by FJ and G on Monday, December 5, 2005 9:40 AM
Over the weekend, I handlayed my first code 148 turnout for my outdoor train shed (shed is last photo). The rails are nickel-silver from Right O way and ties are cedar, stained with honey-color Thompson water seal, temporarily glued to Hardiboard with tile adhesive (if they remain glued outside, that's fine and if the adhesive dissolved over time, that too is fine). Ties are a bit thicker and wider to facilitate spiking and to “bite” into the ballast better. The ties won't look so tall once ballasted.

Spike used are quarter-inch staples, cut to shape.

Since this will be toy train track, there will be a 3rd rail emplaced at some point.

Inside the train shed, btw, is Lionel tubular track with a zinc coating.

I left it out in the rain for a month and detected no noticeable rust (although it might rust from inside out in the tubes; but also sprayed the underside). There's approx. 36 feet of tubular, zinc-coated rail inside the shed with leads running out starting in code 148 & shimmed up. I used a multimeter, and found the zinc to have zero conductivity, surprisingly. However, since only rolling stock is inside the shed and not locomotives, no power to rails is necessary. Below is photo of zinc coating and track testing measure, which BB the beagle is investigating:



Below photo shows ties glued to hardiboard. I was unsure where I wanted the headblock ties so I added a couple extra for good measure to later cut 2 off. This photo represents the 3 lead tracks from the train shed.



layed the outside stock rail and shaved the bottom rail where the points will meet. Every tie needs to be spiked in outdoor operations; unlike indoors!



below shows the next construction view; step 2 being the other stock rail and then the rails leading to the frog and lastly the point/closure rails. Then, cut off the unwanted headblocks.

This is my first handlayed curved turnout. It's a real joy working, as I was able to go with a one-piece point/closure rail, as the rail is small and thin enough to bend without pivoting, as most O and G scale track pivots. The frog is the trickiest part; to ensure the flangeway works in both directions; requiring some spiking and unspiking and testing with rolling stock. I didn't fill the frog, as the dimensions were very exact, allowing free wheel movement.



Below, you can see I altered the original drawing somewhat. I used a compass to measure the track gauge.



Below are components fabbed for switch stand using brass plumbing pipe and stock brass parts. The plumbing pipe was hammered flat and cut with tinsnips, then using the nibbler a channel was cut; then sweated the pieces together with propane torch and resin solder.

The trickiest part is the throw rod, which needs to rotate. I fashioned a rotation using brass rod, soldered to brass nuts. I then cut a portion of a bolt that attaches to the nuts and allows the throw rod to rotate when the switch stand lever is thrown. I soldered the lever to the throw rod as well. Nothing fancy but it works. The assembly is affixed to the headblock ties with brass nails (drilled holes for nails).



below, soldered points to hammered-portion of brass rod.



below, work progressing. Ties will be trimmed once final track is emplaced. Whilst turnouts are mounted on hardiboard, remainder of trackage will float in ballast, secured with Quickrete bonding adhesive; testing and proven by a fellow toy train garden enthusiast in Nevada.





trainshed awaits the 3-track lead


Join our Community!

Our community is FREE to join. To participate you must either login or register for an account.

Search the Community

FREE EMAIL NEWSLETTER

Get the Classic Toy Trains newsletter delivered to your inbox twice a month