To the right side of that closet is the closet for my office. If it weren't for the fact we rent here I'd put a hole through the wall and use 072 curves in there. My office/closet mirror my bedroom/closet.
Modeling the "Fargo Area Rapid Transit" in O scale 3 rail.
Boyd,I plugged your pieces into RR-Track and I don't see a problem with what you are doing. I would get rid of the 120 degree curve and replace it with an O-72. I would then put a 1.75" FasTrack straight between the transition tracks and the O-48 curves.I don't think you will have a problem with cars derailing as long as you aren't running really long trains. I have Atlas O-45 and O-54 curves on my layout with a few S turns and I don't have problems - I keep my heavier cars toward the engines and the lighter cars toward the caboose. If you reverse them then you will have derailments, or if you mix them you might have derailments.If you had more room in the closet I would go with O-72 curves.
My basic question is does it help to have a straight section between a left curve going into a right curve or between a right curve going into a left curve? Here is my youtube video:
http://www.youtube.com/watch?v=Q_KOU12_wN0
The setup I have is not leveled so I have not pulled any cars with an engine over the new portion going into and out of the closet.
Boyd,
How did it work when you set up #2 ? Still not sure if you have a question, or making a statement of an improvement. Just be careful not to step on the track. Good Luck
Don
The difference between the 2 setups is one section outside the closet:
#1. 2 R curve 072 into 1 O half straight into 1 L 072 curve to 52" of straight track.
#2. 2 R curve 072 into 1 L curve 120" circle into 52" of straight track.
Tonight I set it up with the #2 combination. I'll do a video for youtube friday and post a link here.
dbaker48 I am totally lost, I dont think many people will take the time to make a drawing of the pieces you have identified, and then try to anticipate what the question is.
I am totally lost, I dont think many people will take the time to make a drawing of the pieces you have identified, and then try to anticipate what the question is.
I'm still drawing. I should be done in about two weeks, so I can anticipate the
Boyd, ya gotta help us a little bit here. Do you have a derailment problem? If so, try putting short straight sections in between the curved sections.
Celebrating 18 years on the CTT Forum.
Buckeye Riveter......... OTTS Charter Member, a Roseyville Raider and a member of the CTT Forum since 2004..
Jelloway Creek, OH - ELV 1,100 - Home of the Baltimore, Ohio & Wabash RR
TCA 09-64284
Your right, kinda confusing. Understand the track pieces you are using, a diagram would be extremely helpful. Then what are you asking? I couldn't find a question.
Are you asking about transistion pieces?
Grade percentage?
Track compatibility?
Anyone, anyone?
I removed the 3% grade S curve on my layout that uses 48" curve fastrack and am replacing it with a turnaround loop in the closet. When this is all done I think the climbing grade will be below 1.5%. Its not quite finished but here is what I have in the works leading up to closet, then loop then out:
51" of straight O tubular to
three right 072 tubular to
one 5" straight O to Fastrack transiton piece to
3/4 of a circle going left 48" Fastrack to
one 5" straight O to Fastrack transition piece to
two right 072 tubular to
one 5" straight O tubular to
one left 072 tubular to
50" of straight Fastrack.
Today I picked up one section of K-line O tubular 120" curve so I could change the about turnaround loop to:
one left 120" curve section O tubular to
If you all are lost trying to follow this I could film and show it on youtube.
Our community is FREE to join. To participate you must either login or register for an account.
Get the Classic Toy Trains newsletter delivered to your inbox twice a month