Login
or
Register
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Home
»
Model Railroader
»
Forums
»
Electronics and DCC
»
For what it's worth, my little tutorial/method on Atlas/Kato DCC conversions.
Edit topic
Updated your discussion topic below.
Subject
Enter a subject for your topic. Maximum 150 characters.
Post Body
Enter your post below.
<P mce_keep="true">After slightly more than a dozen of these conversions of the older Atlas/Kato and Kato models, I have devised a relatively fast and simple method.....compared to my first few.</P> <P mce_keep="true">So if anyone else has been collecting these little slightly used beauties from places like Dan's Trains (I once got 4 on close-timed auctions for an average of $28 each), this is how I now do them:</P> <P mce_keep="true">At first I was replacing the single incandescent lamp in the middle with a single LED. But after some experimentation, I found I liked: </P> <P mce_keep="true">1. melting* back the headlight bars to the mounting brackets in the shell. A hot iron does this best (although some forum members argued unsucessfully with me about this) as it is very quick, leaves a mirrored "cut" and does not create plastic dust everywhere. This gives space for the decoder and two LEDS on the original plastic platform atop the motor. I have to use nippers to trim off the ridge of melted plastic created on the top remaining end of the bar.</P> <P mce_keep="true"><IMG src="http://i168.photobucket.com/albums/u172/dcrane_2007/3.jpg" mce_src="http://i168.photobucket.com/albums/u172/dcrane_2007/3.jpg"></P> <P mce_keep="true"> 2. I like NCE's D13SRs best as they have the best performance for the price. I have also used tiny Digitrax 123s and 125s</P> <P mce_keep="true">3. Pull out the incandescent bulb and I bend the posts of the LEDs so they will sit on top of the black tabs of the grey plastic board and then with a chisel point soldering tip, just heat them until they "set" down into plastic. Then I trim the LED posts and put on the resistors etc. </P> <P mce_keep="true"><IMG src="http://i168.photobucket.com/albums/u172/dcrane_2007/1.jpg" mce_src="http://i168.photobucket.com/albums/u172/dcrane_2007/1.jpg"></P> <P mce_keep="true">4. I use the same chisel point to smear over enough meted plastic of the grey board to lock in the flat copper motor contacts where they rise up alongside the board. This is handy because they are now held in place when I cut the copper tabs where they contacts the track power strips with a dremel.</P> <P mce_keep="true"><IMG src="http://i168.photobucket.com/albums/u172/dcrane_2007/2.jpg" mce_src="http://i168.photobucket.com/albums/u172/dcrane_2007/2.jpg"></P> <P mce_keep="true">5. Finally, trim the decoder leads to length solder them up and tape down the decoder with kapton tape.</P> <P mce_keep="true"><IMG src="http://i168.photobucket.com/albums/u172/dcrane_2007/7.jpg" mce_src="http://i168.photobucket.com/albums/u172/dcrane_2007/7.jpg"></P> <P mce_keep="true">* I do all melting in the outdoors and with a respirator because the grey plastic on these models is especially vile when melting and it's probably full of nasty toxins. The headlight bars are not nearly so toxic smelling.</P> <P mce_keep="true">Now, the headlight bars come down just before and after the ends of the D13sr decoder and pick up the light perfectly....and I have switchable forward and after beams unlike the original single incandescent bulb.</P> <P mce_keep="true">This particular model is a GP7 and has the nice solid catwalk for a weight. The older models have that fussy detachable catwalk and free-mounted weights that sit on the light bars. A tip with those is to start the day ahead by gluing in the weights with some latex caulk so that they don't keep falling out during manipulation of the shell. If necessary, they can be pulled free in the future. </P> <P mce_keep="true">Now, I don't think I know all the answers, but it is my 2 cents after a dozen installs in these particular models, and I have it down to a pretty smooth operaton now.</P> <P mce_keep="true"> </P>
Tags (Optional)
Tags are keywords that get attached to your post. They are used to categorize your submission and make it easier to search for. To add tags to your post type a tag into the box below and click the "Add Tag" button.
Add Tag
E-mail Subscribe
Check the box below if you want to receive e-mail notifications when replies are made to this thread.
Receive notifications
Update Discussion Topic
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Users Online
There are no community member online
Search the Community
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT
Model Railroader Newsletter
See all
Sign up for our FREE e-newsletter
and get model railroad news in your inbox!
Sign up