Trains.com

Subscriber & Member Login

Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!

Spray paint

2962 views
13 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    March 2017
  • 8,173 posts
Posted by Track fiddler on Friday, October 6, 2023 8:12 PM

Hi Fred, My buddy Terry texted me from our past Model Railroad Club after Gary unfortunately died.

This spray paint is available through Kevin's neck of the woods at the Home Depot.  It has an ever so fine spray nozzle and Gary swore by it.

Model of the Minneapolis Depot by Terry

 

I'm not into metallic paint for modeling, but will be painting one of my bridges with this paint to check it out.  It's available in other colour selections, and came highly recommended.

 

TF

 

 

  • Member since
    January 2017
  • From: Southern Florida Gulf Coast
  • 18,255 posts
Posted by SeeYou190 on Friday, October 6, 2023 7:50 PM

Follow up... I see NAPA still offers Martin Senour spray paints, but they do not show the nozzle.

Given the low price, I doubt it is the same nozzle I was so impressed with.

I remember paying around $15.00 a can for this twenty years ago.

-Kevin

Living the dream.

  • Member since
    January 2017
  • From: Southern Florida Gulf Coast
  • 18,255 posts
Posted by SeeYou190 on Friday, October 6, 2023 7:28 PM

Fred... I will start by saying Tamiya is great.

However, the best spray paint can I have ever used was the Martin Senour line from NAPA with the metal needle valve on top of the can.

I don't know if it made any more.

-Kevin

Living the dream.

  • Member since
    March 2009
  • 108 posts
Posted by derf on Friday, October 6, 2023 1:06 PM

Thanks everyone for your suggestions and tips.

Fred

  • Member since
    March 2012
  • 1,162 posts
Posted by PC101 on Monday, October 2, 2023 7:50 PM

I have seen this used as an ''edge softner'', cut a few ''clouds'' out of a piece of cereal box cardboard and while holding the cardboard about 3'' away from the surface you want the cloud to be on, then spray. Light color for the whole cloud and a shade darker on the lower/bottom of the cloud. I did not stick around to see the finished job up close to see the results. Test first on something that will not matter what the the outcome is.

The light puff-puff-puff application as mentioned above works good.

 

  • Member since
    February 2008
  • 2,360 posts
Posted by kasskaboose on Monday, October 2, 2023 6:43 PM

I hope you're using the spray paint with a mask, ventilator, or outdoors.

  • Member since
    February 2002
  • From: Mpls/St.Paul
  • 13,892 posts
Posted by wjstix on Monday, October 2, 2023 9:51 AM

I use Tamiya spray can paints on locomotives, cars, and buildings. However, for adding clouds, I use Testor's. I find the Tamiya paint tends to hit the backdrop and run down in streaks, where the Testors stays put better. Best to use light puff-puff-puff applications rather than trying to hold the nozzle down when spraying.

Stix
  • Member since
    July 2006
  • From: Bradford, Ontario
  • 15,797 posts
Posted by hon30critter on Sunday, October 1, 2023 4:35 PM

Hi Fred,

You might try wiping the nozzle frequently. Paint buildup there can cause spattering.

Thorough mixing is essential!!! Shaka shaka!

As was suggested, warming the can will help.

I would also suggest that if you are only putting down a very light coat of paint, you can probably get away with one or two cans unless your backdrops are very large.

One of my club's members used a regular rattle can to spray very good looking clouds on the walls around our layout. Granted the clouds were a little more dense than what you would like, but any individual paint dots around the egdes were not visible. Keep in mind that the clouds will not be a focal point. They are a background accent. Nobody (except you) is going to study them with a magnifying glass.

I do not recommend Testers spray cans (as opposed to Tamiya). They put out a lot of paint in a hurry and I think that would make them difficult to use for your purposes.

Cheers!!

Dave

I'm just a dude with a bad back having a lot of fun with model trains, and finally building a layout!

  • Member since
    September 2014
  • From: 10,430’ (3,179 m)
  • 2,311 posts
Posted by jjdamnit on Saturday, September 30, 2023 2:16 PM

Hello All,

I use rattle can paints for a great number of projects.

Especially where uniform coverage over a large area is needed and- -I don't want to set up my airbrush.

I use the "Bain-Marie" method to heat the can(s).

They are soaked in hot tap water until they are at the same temperature as the water; shaking them for 30 seconds every few minutes.

Do Not Use Boiling Water! Hot Tap Water Only!

My paints are stored in an unheated attached porch and usually require 2 to 3 changes of hot tap water to get them up to temp.

By using this method it achieves two (2) things:

  • Slightly increases the pressure of the propellent as heat expands gasses.

  • Thins the paint for a finer mist to avoid obscuring fine details. This is especially helpful when using "primers."

When painting large areas refreshing the heat in the can, with additional soaks in hot tap water may be necessary.

Hope this helps.

"Uhh...I didn’t know it was 'impossible' I just made it work...sorry"

Moderator
  • Member since
    June 2003
  • From: Northeast OH
  • 17,255 posts
Posted by tstage on Saturday, September 30, 2023 1:40 PM

Fred,

Tamiya makes gloss, semi-gloss, and flat spray paints in lacquer and acrylic.  The spray paint cans are small so using them for a backdrop could be cost prohibitive?  If only for clouds though, it could still be a reasonable option for you.  I mainly use the semi-gloss paints for locomitive and rolling stock.

Tom

https://tstage9.wixsite.com/nyc-modeling

Time...It marches on...without ever turning around to see if anyone is even keeping in step.

  • Member since
    March 2009
  • 108 posts
Posted by derf on Saturday, September 30, 2023 10:55 AM

Tom,

Wouldn't the lacquer show up shiny, especially on a backdrop or does it dry flat?

Fred

Moderator
  • Member since
    June 2003
  • From: Northeast OH
  • 17,255 posts
Posted by tstage on Saturday, September 30, 2023 10:29 AM

Fred,

I'll 2nd the Tamiya recommendation.  I primarily use their "TS" (lacquer) line of spray paints and have been very happy with their product.  It sprays on very evenly and dries quickly.  My only complaint is that I wish Tamiya made their spray cans in larger sizes - like they do with their primers.

Tom

https://tstage9.wixsite.com/nyc-modeling

Time...It marches on...without ever turning around to see if anyone is even keeping in step.

  • Member since
    January 2014
  • 1,500 posts
Posted by ROBERT PETRICK on Saturday, September 30, 2023 9:01 AM

Tamiya produces a line of spray paints that seem to meet your criteria. I've had good luck with their fine mist qualities. 

LINK to SNSR Blog


  • Member since
    March 2009
  • 108 posts
Spray paint
Posted by derf on Saturday, September 30, 2023 8:18 AM

Is there a rattle can spray paint that has a fine spray as opposed to the normal big box cans that blow larger blobs? I know an air brush would work, but I don't have one. I'm wanting to spray a light mist over my backdrop to look like the clouds that are miles away.

Fred

Subscriber & Member Login

Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!

Users Online

There are no community member online

Search the Community

ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT
Model Railroader Newsletter See all
Sign up for our FREE e-newsletter and get model railroad news in your inbox!