Trains.com

Toronto Streetcar Question

3929 views
12 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    February 2011
  • 117 posts
Toronto Streetcar Question
Posted by sandyhookken on Wednesday, January 5, 2022 8:20 PM

While I was watching several videos on YouTube of Toronto streetcar routes taken from the driver's view out of the front winshield, I noticed several signs in the overhead wiring. These looked to be blue with white lettering reading "NA". Can anyone explain their meaning?

  • Member since
    June 2002
  • 20,096 posts
Posted by daveklepper on Wednesday, January 5, 2022 9:27 PM

Were they located just before facing-point switches?

  • Member since
    February 2011
  • 117 posts
Posted by sandyhookken on Thursday, January 6, 2022 10:03 AM

Yes

  • Member since
    September 2010
  • 2,515 posts
Posted by Electroliner 1935 on Thursday, January 6, 2022 3:58 PM

Facing Point Switches that were active were controlled by a sensor in advance of the switch that was controled by a "Power ON/OFF" sensor. I suspect that the sign you saw was to indicate the switch you saw had been made manual and the sign indicates Not Active. But I would hope someone more knowlegeable would confirm my supposition. Can you post the link to the video you saw so I can see it.

  • Member since
    July 2008
  • 2,325 posts
Posted by rdamon on Thursday, January 6, 2022 5:20 PM

Is it this?

 

 

  • Member since
    February 2011
  • 117 posts
Posted by sandyhookken on Thursday, January 6, 2022 7:10 PM

That's it.

  • Member since
    July 2008
  • 2,325 posts
Posted by rdamon on Thursday, January 6, 2022 8:19 PM

Found this 

"To say the least. There are more out of service electronic switches than serviceable ones at the moment. Whenever you see one of those green signs hanging from the streetcar wires that says "NA" with an arrow pointing in a certain direction - that's an electronic switch. NA means "Necessary Action" - which means the operator has to press a button if they want to go in the direction of the arrow. There is a coil onboard the streetcar that broadcasts a low frequency signal which is picked up by a loop in the switch and voila, the switch actuates. Most of these green signs are currently covered with yellow ones that say the switch is out of service and must be used manually."

  • Member since
    December 2008
  • From: Toronto, Canada
  • 2,560 posts
Posted by 54light15 on Thursday, January 6, 2022 9:38 PM

Normally when the car changes the route, the driver uses the switch iron to move the points. It takes a bit of muscle to do that. When there is a diversion, say the Westbound Queen car went down to King at Church and is going back to Queen at Bathurst, there will be a guy sitting there with the iron so the driver doesn't have to get out and do it. But sometimes the remote control will actually work but that is rare. 

  • Member since
    July 2006
  • 1,530 posts
Posted by NKP guy on Friday, January 7, 2022 10:45 AM

  I recall in 1964 riding a PCC in Pittsburgh quite near the PRR station.  The switches there were controlled by a toggle on the motorman's dashboard; no getting out with a switch iron.  I was given to understand these were common there, at least downtown.

   I especially enjoyed watching the motorman operate these switches in wet weather, because with a flick of his wrist from inside, the switch movement forced a small jet of water straight up, startling unsuspecting pedestrians nearby!

  • Member since
    September 2010
  • 2,515 posts
Posted by Electroliner 1935 on Friday, January 7, 2022 7:22 PM

At one time, they used a short section where the motorman had to either coast through an area or have power on through the section which would determine the switch operation. I believe it was sensitive to the amount of power (amperage) that the car drew as to whether it actuated or not. Car lights, heat and air compressor were not enough to trigger but motor power was. This was also used on some trolley bus overhead switches

  • Member since
    June 2002
  • 20,096 posts
Posted by daveklepper on Saturday, January 8, 2022 11:11 AM

The two systems described above are identlcal.  The Toronto Peter-Witt cars did not have the switch and use power-on, power-off.  The Pittsburgh Peter-Witts akso did not have the switch.  Ditto Brooklyn.

For the power-on - powser-off system to work safely, the operator must have  the ability to both power the motors and brake at the same time.  The PCC basic control system prevents this, since motors are in dynamic-brake-mode whenever brakes are applied.  Thus the PCC cars have the "action" switch to run current through a resistor, replacing the motor current.

The Thord Avenue and the Omaha and Coucil Bluffs systems did not employ any electric track switches, since the combination "dead-man's" pedal - lift-foot-to-brake - lift-foot-to-oprn-door control also does not permit simultaneous braking and powering. And the PCC-equiped action swtch and bypass resistor is lacking.  Important junctions did have switch tenders.  On Third Avenue, at 42nd Street & 7th Avenue (Times Squre).  West Farms Square, 181st & Broadway, and Gettys Square, Yonkers, a switchman's shack included a large lever with a mechanical connection to a switch-point.  In Yonkers, two levers.

  • Member since
    July 2010
  • From: Louisiana
  • 2,310 posts
Posted by Paul of Covington on Saturday, January 8, 2022 10:15 PM

Electroliner 1935

At one time, they used a short section where the motorman had to either coast through an area or have power on through the section which would determine the switch operation. I believe it was sensitive to the amount of power (amperage) that the car drew as to whether it actuated or not. Car lights, heat and air compressor were not enough to trigger but motor power was. This was also used on some trolley bus overhead switches

 

   As far as I know, this method is still used in New Orleans.  I remember seeing the motorman rapidly sweeping the throttle back and forth while the car coasted slowly through a curve where there were switches.

_____________ 

  "A stranger's just a friend you ain't met yet." --- Dave Gardner

  • Member since
    February 2011
  • 117 posts
Posted by sandyhookken on Thursday, February 10, 2022 10:35 AM

Thanks to all who responded to my question. I recently heard from a friend who lives in the Toronto area who's neighbor works for the TTC, and who explained why the "NA" turnout control system is not being maintained. The new Flexity streetcars use a new wireless control ystem; the "NA" signs are being removed during routine overhead wire maintenance.

Join our Community!

Our community is FREE to join. To participate you must either login or register for an account.

Search the Community

Newsletter Sign-Up

By signing up you may also receive occasional reader surveys and special offers from Trains magazine.Please view our privacy policy