gmpullman My Empire State Express locomotive seems to be fine running on a Digitrax DCC system. Too many acronyms! Regards, Ed
My Empire State Express locomotive seems to be fine running on a Digitrax DCC system.
Too many acronyms!
Regards, Ed
Ditto on my Lenz system. If I didn't know it was DCS instead of DCC, I would never have figured it out. The streamlined ESE Hudson is probably my favorite steamer.
Southgate 2PS what's DCS?
In my case DCS is the Digitrax model designation for their Digital Command Station.
https://www.digitrax.com/products/command-stations-boosters/dcs240plus/
I have only one locomotive from the old "Mike's Train House" and that has the proprietary Digital Command System. In later years MTH conceded a bit and made DCC integration a "feature" since they may have been seeing market share erode due to sticking with the strictly DCS arrangement.
https://dccwiki.com/Digital_Command_System
MTH's proprietary operating system. Although DCS-equipped locomotives will operate on DCC, you need a DCS throttle/power pack to fully-utilize the MTH decoders.
Tom
https://tstage9.wixsite.com/nyc-modeling
Time...It marches on...without ever turning around to see if anyone is even keeping in step.
Great setup Ed! My layout room doubles as activity center, thus the layout is at 4'10". I'm 6'1" so no prob.
That leaves the 19×9+ lower half for benches full length on one side and about 15 ok n the other.
I'm sure that when you built that "drawing" cabinet, those wheels were already turning!
Dan
PS what's DCS?
Shop-Door by Edmund, on Flickr
I don't believe I've ever had the inclination to photograph my test track in recent memory. This basement room was once an architect's "studio" and when she moved out I quickly adapted it to a model railroad "activity center".
Test Lab-L by Edmund, on Flickr
I have a "coach yard" track coming through the wall from the layout to a seven-track storage area and the test track is just above it behind the green protective edge. It is sixteen feet long.
Test Lab by Edmund, on Flickr
I have a rotary switch whereby I can select the ESU Lokprogrammer or a Sprogg JMRI programming application or a third position connecting an MRC tech something DC supply.
I use banana plugs as the interface and if needed I can easily plug in an RRamp meter or an old Digitrax DCS 200 if desired. Plus there's a cable leading out to the paint booth so I can use a short length of trasck in there with just enough throttle to turn the wheels while painting weathering on to the running gear.
Test Lab-S by Edmund, on Flickr
I made those drawers in the back there to store flat drawings but they were easily adapted to HO equipment
Drawers_aplenty by Edmund, on Flickr
As you can see, any horizontal surface gets quickly cluttered. Spring cleaning is coming soon
The architect left behing her drafting board for me and it makes a fine work area:
IMG_7287_fix by Edmund, on Flickr
This is an older photo.
I spend hours in this environment and enjoy every minute of it.
Cheers, Ed
My test track is a 48" piece of 1x4 with an Atlas track stop on one end, a rerailer on that end followed by 41" of track and a Kadee height gauge glued to an insulated section of track on the other. DC power is fed on the track stop end via a special wire that connects to the rail. Powered with a spare MRC power pack I have.
I don't have a workbench test track. It's a short walk from my workbench to the layout so why go to the trouble of using up workbench space for a test track and having to wire it up. What is it going to tell me running a loco on a couple of feet of straight track? My programming track doubles as a coupler height check using the Kadee tool. To test locos, I just put it on a convenient section of the layout and run it through its paces, around curves, through turnouts etc. I test my rolling stock by pushing it over the crest of a long 1.75% grade. If it coasts all the way down the grade, around a curve at the bottom, and well into a flat section without derailing, I know it's rolling well.
None for now. I stole the 2 flex code 70 off my 6 foot long 1x4 to use on the layout, intending to replace with code 100, which my LHS is perpetually out of. Dan
Mine is two pieces of flextrack, mounted on my workbench, MRC 2400 with test leads and alligator clips. Works fine. I also have a yard lead to the left of my workbench so that turns into a test track as well at times.
I do think those MicroMark rollers would be useful. I'll have to look into getting some.
No test track. The train room is three short half flights of stairs up from the basement. Testing to me is testing everything, lights and sound included. So I need a full DCC system for testing, and I've only got one system.
My train tools are all up there anyway.
It takes an iron man to play with a toy iron horse.
Hello All,
Mine is a 30-inch piece of 1"x4" with three 9-inch sections of straight track. The center piece is a rerailer.
On one end two (2) wires are soldered to each rail, the opposite end has two (2) wires soldered to the rails with a connector to attach an MRC Decoder Dr.
A Digitrax PR3 is connected via the other two (2) wires, which is connected to my Mac Mini; via a USB cable, running DecoderPro.
This setup is more of a programming track rather than a "Test Track."
My DCC system is an NCE Power Pro, but I don't use the "Programming Track" outputs from the command station/booster.
If I need DC power I have a Bachmann DC controller with alligator clips. I disconnect the wires at the PR3 and clip them to the DC controller.
The DC controller can also test motors before installation.
To calculate the stall current I can attach a multi-meter between the DC controller and the motor, with a jumper wire with alligator clips on both ends.
I have considered rollers for breaking in locomotives but have never gotten around to purchasing them. I just run the locomotive(s) around the "mainline" of my 4'x8' pike.
Hope this helps.
"Uhh...I didn’t know it was 'impossible' I just made it work...sorry"
This is a great forum topic and one that has not been much explored.
I think that a lot depends upon what the user expects to accomplish with a "test track" on the work bench. As several replies have already indicated, a strip of flextrack connected to a power source is basic and may suffice if the purpose of the test track is merely to test whether a locomotive runs forward and backward and the lights work.
A set of rollers is extremely useful in order to run a locomotive in place and a real space saver as opposed to trying to test on 10 or 20 feet of track.
One thing that I do since I run a DCC layout is to leave the power off and clip two wires from a DC power pack to the mainline when testing newly acquired DCC Ready locomotives.
Whenever I have a need to test a DCC powered locomotive, I do it on the layout and I often use a set of rollers to run the locomotive in place. I test decoders using a Decoder Tester and then I program the decoder on the Programming Track supplied with my system.
So, that is how I address the issue of a test track on the work bench.
Something that I fantasize over but have yet to do is to setup what I call a "test lab" on the work bench. My layout is powered by an NCE PH-Pro 5 amp wireless DCC system. I yearn to purchase a Power Cab to test not only locomotives but also signal systems and route automation on a DCC powered mini-layout on a sizeable work bench. Right now, I have to experiment with such testing on my main layout which means that I have to cease normal operations to do testing.
Rich
Alton Junction
mobilman44 For about 25 years, I've used a 3 ft "1x4" with a strip of code 100 track and an Atlas bumper on either end. The track is set on cork roadbed and the whole thing is painted grey. The track is wired to two thumb screw terminals set on one end of the board, which allows quick change from an RMC DC pack to a Digitrax DCC controller. This unit is obviously very portable and when in use I have an NMRA coupler guage and a set of 6 rollers - which were expensive, but definitely worthy. One thing I used this test track for was "rollability" of cars. I would put a 1/2 or 3/4 inch block under one end, and set cars on the high end to see if they rolled - or not. It worked well for me, assuring that every car had similar rolling ability.
For about 25 years, I've used a 3 ft "1x4" with a strip of code 100 track and an Atlas bumper on either end. The track is set on cork roadbed and the whole thing is painted grey.
The track is wired to two thumb screw terminals set on one end of the board, which allows quick change from an RMC DC pack to a Digitrax DCC controller.
This unit is obviously very portable and when in use I have an NMRA coupler guage and a set of 6 rollers - which were expensive, but definitely worthy.
One thing I used this test track for was "rollability" of cars. I would put a 1/2 or 3/4 inch block under one end, and set cars on the high end to see if they rolled - or not. It worked well for me, assuring that every car had similar rolling ability.
I have never had a test track on my workbench. I use some Kato Unitrack set up on either the dining room table or the kitchen counter.
-Photograph by Kevin Parson
This has worked well for me.
-Kevin
Living the dream.
ENJOY !
Mobilman44
Living in southeast Texas, formerly modeling the "postwar" Santa Fe and Illinois Central
"One difference between pessimists and optimists is that while pessimists are more often right, optimists have far more fun."
Little TimmyI just use a 3 foot section of flextrak and a thriftstore MRC power-pack
I do exactly the same thing, but I have two 3' sections of track. One can be powered by a DC throttle or my NCE Powercab and the other is used when I am using my Lokprogrammer. I just put the bare tracks on my workbench or my computer desk.
However, I need to get my butt in gear and install at least one loop on my long neglected layout so I can do some speed matching and other programming without being limited by the short pieces of track.
Cheers!!
Dave
I'm just a dude with a bad back having a lot of fun with model trains, and finally building a layout!
I don't have a pic, but... our club/museum has a pair of 6'-or-so tracks. One is plain hand-laid rail (no ties) and connects to our old home-built DC power supply and an NCE throttle (funny 'cause we're a Digitrax club). A switch on the old power supply toggles between DC and DCC. Next to it is another track which is connected to the DCC programming computer (running Decoder Pro).
Aaron
It had the original box and it is marked Philadelphia 33 so she is pushing 60 years old but still works fine. slender man wallpaper
Not really. DCC, DCS, or DC all require a wire to each rail and alligator clips work just great for hooking up any one of those to your test track. Disconnect them from one power source to a different power source and you're ready to go. Simple.
All that you need but the DCS guys need a more elaborate set up .
I just use a 3 foot section of flextrak and a thriftstore MRC power-pack connected with whatever wires I happen to have lying around.
Totall cost ... about 5 bucks.
Rust...... It's a good thing !
Attached above the work bench working area is 6' of HO code 100 NS track compleat with two rearailer nailed down to cork roadbed on a wood shelf with Hayes style wheel stops attached at each end of the rail backed up by soft foam on a wood block. DCC electric power, Lenz system, is ran through a double pole double throw center off bat switch (always in the ''off'' position till I want the test track powered) to have "program" or "main" power. I have those stationary run-in-place roller bearing testing items that look like what Tstage has (may be Bachmann, IDNR?).
Hey whatever works !
My layout is close to my workbench so I use it to do the the testing. I have a $2 tyco power pack for testing motors and stuff.
The ones pictured are from Micro-Mark. They are a friction-fit between the rails. The Bachmann version I find convenient underneath tenders because they are easier to reposition.
I just have a scrap of 1/2" plywood with piece of track approximately 15 inches long. Enough to move back and forth, not much else. If I need or want to do more, I've got a loop of sectional track I just put on the dining room table.
Control and programing is supplied via an Arduino and JMRI.
Nice !(I really like that brass boxcab but zi think that it is weird that it is powered by springs but better than the old Atherarn rubber band drive!)I gave a set of four Bachmann rollers like that and they work ,but I don't like the fact that the magnets that hold it to the track are rather weak .
Mine is roughly 24" long and outfitted with several roller bearing stands, which allows me to test or break-in a locomotive stationary. I use alligator clips to connect the track to either my NCE Power Cab (DCC) or my DC power supply.