rrebell So if you just have a simple layout with one reversing track needed will the AR-1 do the job, they are only $25.
So if you just have a simple layout with one reversing track needed will the AR-1 do the job, they are only $25.
Rich
Alton Junction
Thanks, Randy.
The BXPA1 is $38 at Tony's, PSX-AR is $54. Feedback PSX-AR (to get the block detection feedback) is even more. The BXPA has 2 poteiometers to tune trip speed and current, no need to mess with CVs.
Af far as the EB1 and PSX - about the only thing missing is the optional detection. The EB1 had remote indicator and remote reset options, and a very configurable ramp up to handle sound loco inrush - there are like 8 points you can set via CV to gradually restore the power and ignore inrush, though you don't need to use all of them if the basic settings happen to work. And there are no multiple EB1s, they are all singles, no dual, triple, or quad like a PSX - but the newer PSX don't link the inputs together anyway like the old ones, so buying a quad PSX is like getting 4 PSX1s, only you the purchaser have to snap the circuit boards apart - unless you need 4 in one place, then I suppose you could say the mounting was a bit simpler since all 4 together can be mounted with 4 screws, it takes more screws to mount 4 single boards.
--Randy
Modeling the Reading Railroad in the 1950's
Visit my web site at www.readingeastpenn.com for construction updates, DCC Info, and more.
rrinker For breakers I'd just as soon use the EB-1 from NCE, they are solid state like the PSX and have 99% of the features for a lower cost.
For breakers I'd just as soon use the EB-1 from NCE, they are solid state like the PSX and have 99% of the features for a lower cost.
rrinker NCE has an all electronic one now as well. Though for whatever reason, it is priced higher than a PSX-AR.
NCE has an all electronic one now as well. Though for whatever reason, it is priced higher than a PSX-AR.
rrinker The AR-1 has been sort of replaced with the BXPA1, which is both an autoreverser, a breaker, and a track detector - all soild state, no relays. Trip amps and trip speed easily set with potentiometers.
The AR-1 has been sort of replaced with the BXPA1, which is both an autoreverser, a breaker, and a track detector - all soild state, no relays. Trip amps and trip speed easily set with potentiometers.
rrinker Though on several layouts I've helped with there has never been a problem with the much simpler Digitrax AR-1. Relays do not equal bad.
Though on several layouts I've helped with there has never been a problem with the much simpler Digitrax AR-1. Relays do not equal bad.
wjstixOne thing I like about the AR-1 is that there's a pot to adjust the sensitivity of the detection circuit.
Brent
"All of the world's problems are the result of the difference between how we think and how the world works."
One thing I like about the AR-1 is that there's a pot to adjust the sensitivity of the detection circuit. Over the years several people have put up posts about their autoreverser not working, and it turned out it was because they bought one that wasn't adjustable. When they replaced it with the AR-1, their reverse loop worked fine.
hon30critterI will upgrade to an NCE 5 amp wireless system once the layout is operational.
I love mine! Why does everything in my house involve puppies? They love it too.
NCE has an all electronic one now as well. Though for whatever reason, it is priced higher than a PSX-AR. For breakers I'd just as soon use the EB-1 from NCE, they are solid state like the PSX and have 99% of the features for a lower cost.
Though on several layouts I've helped with there has never been a problem with the much simpler Digitrax AR-1. Relays do not equal bad. And I never had a problem with my PM-42, either. Even deliberately attempting to cause problems by putting all my sound locos int he same section and shorting it. I know people have said they had problems with it not resetting with just ONE sound loco - to that I say, check your wiring. Because I had at the time 5 sound locos plus a couple of non-sound sitting in one section of the breaker, I shorted the track, the power cut out as expected, but only the one section of the breaker, other track had power, when I removed the short, all my sound locos started up again. No inrush problem. However, a PM-42 is really only usable for Digitrax layouts because that is the only way to configure the trip current.
I can't recommend the DCC Specialties PSX-AR enough. I have 12 of them on my layout that cover 2 levels, a turntable and WYE. They work flawlessly and very happy with them.
hon30critter ROBERT PETRICK You could also isolate the entire yard by gapping #11 and #A (or the point to the right of #A just off the edge of the image). But I don't know if the circuitry of your AR can carry the load of a bunch of engines in the yard. Hi Robert, First, thanks to you and Randy for your responses. I haven't purchased an auto reverser yet so my choices are wide open. I am currently using an NCE Power Cab but I will upgrade to an NCE 5 amp wireless system once the layout is operational. I'll have to spend more time studying the issue. I'm a bit slow when it comes to figuring these things out. Dave
ROBERT PETRICK You could also isolate the entire yard by gapping #11 and #A (or the point to the right of #A just off the edge of the image). But I don't know if the circuitry of your AR can carry the load of a bunch of engines in the yard.
Hi Robert,
First, thanks to you and Randy for your responses.
I haven't purchased an auto reverser yet so my choices are wide open. I am currently using an NCE Power Cab but I will upgrade to an NCE 5 amp wireless system once the layout is operational.
I'll have to spend more time studying the issue. I'm a bit slow when it comes to figuring these things out.
Dave
ROBERT PETRICKYou could also isolate the entire yard by gapping #11 and #A (or the point to the right of #A just off the edge of the image). But I don't know if the circuitry of your AR can carry the load of a bunch of engines in the yard.
I'm just a dude with a bad back having a lot of fun with model trains, and finally building a layout!
My balloon track is 13' long and if I cut out behind the baggage cars I can turn a passenger train. The balloon track is closest to the RH and has the PSX-Ar and it has worked flawlessly for years. The gaps are right at the turnouts on either end.
hon30critter Can I ask how an auto reverser works in the case of a wye? In particular, where would the gaps be in this example? Some trains will be longer than the legs of the wye. How will this work? Thanks, Dave
Can I ask how an auto reverser works in the case of a wye? In particular, where would the gaps be in this example? Some trains will be longer than the legs of the wye. How will this work?
Thanks,
I agree with what Randy said (of course!).
You could also isolate the entire yard by gapping #11 and #A (or the point to the right of #A just off the edge of the image). But I don't know if the circuitry of your AR can carry the load of a bunch of engines in the yard.
My situation is similar, and I use a Digitrax booster configured as an auto-reverser. I don't know the details of your power and control systems.
Robert
LINK to SNSR Blog
It works the exact same way. The easiest thing for a wye is to isolate the tail and connect the AR there. If you pay attention when wiring the feeders, the main side plus one leg will have the same polarity all the time. Only the second leg will need the feeders reversed to match the main. So if you isolate the tail section, that is the only place where a mismatch will occure, when coming in from one leg and leaving via the other.
However, with the yard and all the complicated track across the top - it might be easier to isolat the lower leg, the one that is just a simple curved piece of track from the turnout int he yard to the turnout int he main. The top leg, adn the entire yard, would match the main so there would be no conflicts through there. But that means that lower leg needs to be long enough to handle the longest train. It looks like it is longer than the track in the yard after the turnout - you can compute the length in 3rd PlanIt and verify that, which would make it virtually impossible to bring a train through there longer than the leg of the wye - it wouldn;t clear the turnout into the yard
basementdweller Thanks everyone, it makes sense how, when, and why the auto reverser changes the polarity, my thinking was off some what.
Thanks everyone, it makes sense how, when, and why the auto reverser changes the polarity, my thinking was off some what.
Okay, good.
But even if you're careful and make sure all trains are shorter than the reversing section, there is one other thing to think about.
Two trains going whatever direction cannot cross both gaps at the same time or a short and a shutdown will result. Usually not a problem for a single operator. But sometimes there might be another operator who has a tendency to tailgate or who doesn't look ahead to see if the RS is already occupied . . .
Good luck.
As to why I need to do this. Currently I do not need an auto reverser but I am considering a change to my track plan and I know it will create a reverse loop. I am planning ahead so the reversing section is gapped properly and large enough.
I appreciate the info about the solid state digital vs the manual relay AR. Thanks.
basementdweller The isolated section of track that the auto reverser is wired to has to be longer than the longest train that I intend to run due to metal wheels bridging the rail gaps / isolating track joiners. So the entire train is on the isolated section when the polarity reverses. Do I have that right?
The isolated section of track that the auto reverser is wired to has to be longer than the longest train that I intend to run due to metal wheels bridging the rail gaps / isolating track joiners. So the entire train is on the isolated section when the polarity reverses.
Do I have that right?
I hate to jump into auto-reverser discussions, because I always seem to add more confusion. But I don't think the OP's second question has been answered yet.
A reversing section (RS) has two gaps, one at each end.
When a loco enters a RS and the polarity of the section it is leaving matches the polarity of the RS, nothing happens. If the polarities don't match, the metal wheels of the loco causes a short and the AR responds by switching the polarity of the RS to match the polarity of the section the train came from.
While the train is completely within the RS, the metal wheels of the trailing cars have no effect while crossing the rear gap.
When the loco reaches the gap up ahead and the polarity of the next section matches, then nothing happens. If the polarity of the next section doesn't match, then the metal wheels of the loco causes a short and the polarity of the RS switches and the RS no longer matches the previous section behind. Any metal wheels still behind the first gap will cause a short and provoke a reaction from the AR.
Moral of the story: RS track length must be longer than the train. Or, use plastic wheels on all rear dragging rolling stock.
Hope this helps.
Hello All,
basementdwellerI am contemplating having a reverse loop on my DCC layout, I understand the auto reverser has to be specific to DCC.
A track plan always helps in these situations.
What is the purpose of the reverse loop?
basementdwellerIs there any difference between brands of auto reverser as far as quality, reliability, ease of installation etc?
Absolutely!
However, all National Model Rail Association (NMRA) standards-compliant auto reversers produce the same results.
How they achieve this "standard" can be quite different.
Some DCC manufacturers build this function into their boosters.
Other aftermarket devices, that adhere to NMRA standards, do this in a "different" ways.
On my pike the reversing wye is powered by an MRC AD520 Auto Reverse unit.
This is a simple device but the application can be confusing.
Beyond the recommendations of the fine folks on these forums, I suggest the following web sites:
As well as DCC manufacturers' websites: Digitrax, M.R.C. & NCE.
I also recommend the Digitrax book: Big Book of DCC along with The Complete Atlas Wiring Book.
"Uhh...I didn’t know it was 'impossible' I just made it work...sorry"
richhotrain basementdweller So the entire train is on the isolated section when the polarity reverses. Do I have that right?
basementdweller So the entire train is on the isolated section when the polarity reverses. Do I have that right?
So the entire train is on the isolated section when the polarity reverses.
If the polarity inside the reversing section does not match the polarity of the non-reversing section that the train is leaving, the polarity inside the reversing section will flip immediately to match the polarity of the non-reversing section.
Once the entire train is inside the reversing section, the polarity inside the reversing section will not change until the lead loco begins to exit the reversing section.
If the polarity of the non-reversing section that the train is entering does not match the polarity inside the reversing section, then the polarity inside the reversing section will flip to match the polarity of the non-reversing section that the train is entering.
basementdwellerSo the entire train is on the isolated section when the polarity reverses.
I think you understand the concept, but that is not the way to state it, because the train can enter the loop and the polarity might need to be changed, but most of the train is still outside the isolated section. The first wheels trigger the reversal and all the wheel sets after that are fat and happy.
The polarity should not change again (if the isolated section is too short, it would) until the rest of the train is in the isolated section.
As to your first point, some reversers do not play nice with some of the faster circuit breakers. The CB on the non isolated section detects a short and shuts down before the reverser does it's thing.
Henry
COB Potomac & Northern
Shenandoah Valley
basementdweller Two questions: Is there any difference between brands of auto reverser as far as quality, reliability, ease of installation etc? The isolated section of track that the auto reverser is wired to has to be longer than the longest train that I intend to run due to metal wheels bridging the rail gaps / isolating track joiners. So the entire train is on the isolated section when the polarity reverses. Do I have that right?
Two questions:
Is there any difference between brands of auto reverser as far as quality, reliability, ease of installation etc?
As soon as the lead loco enters the reversing section, the polarity flips inside the reversing section to match the polarity of the non-reversing section that the train is leaving. As soon as the lead loco exits the reversing section, the polarity flips inside the reversing section to match the polarity of the non-reversing section that the train is entering.
I am almost to that point also.
I am contemplating having a reverse loop on my DCC layout, I understand the auto reverser has to be specific to DCC.
Any other advice or comments are appreciated. Thanks.