Just wonder what the rest of you do and if you feel it was the right decision?
I don't solder turnouts. Everything I have read says if you need to service or replace a turnout you can slip back the rail connector until the turnout is free and then replace it the same way.
I solder every joint, including switches. It requires less feeders and you get a solid joint on all these connections and no kinks either.
Some say don't do that, I don't understand why not. And un-soldering the joint is very easy if I have to remove a switch or section of track.
Michael
CEO- Mile-HI-RailroadPrototype: D&RGW Moffat Line 1989
You're going to get a multitude of opinions and "how to's". The "right decision" will be whatever you think is best for you.
Over the years, I have learned that electric model railroad engines need a constant supply of electricity to run . Turnouts are one the most troublesome places to maintain electrical contact. In a turnout (switch), there are many things that can cause a break in continuity or cause the loco to "raise up" and lose contact: point rail, closure rail, frog, guard rail (not to mention any ballast that may get stuck in these small spaces). It is important to maintain electrical contact through these; so, your choices are to run feeders to every piece of rail or solder the joints to maintain electrical supply.
My method: I run feeders to my turnout joints (all 6) AND solder them.
Inspired by Addiction
See more on my YouTube Channel
I solder the joints at the point-end of the turnout. I'm using Peco Electrofrog turnouts and have insulating joiners on the ends of the two frog rails. The other two rails at the frog end are not soldered. This way I can connect power leads to either the turnout itself or the track connected (soldered) to the point end of the turnout. The important thing to remember is not to rely on loose unsoldered rail joiners to carry power from one section of track/turnout to the next. You don't have to solder every joint as long as you have power connected to those track sections not receiving power from another powered track section through a soldered joint.
Bob
Motley I solder every joint, including switches. It requires less feeders and you get a solid joint on all these connections and no kinks either. Some say don't do that, I don't understand why not. And un-soldering the joint is very easy if I have to remove a switch or section of track.
Same here, have been since the 1960's. Soldered rail joints mean no electrical problems.
Sheldon
If your layout is located in a NASA clean room, where the variances in temperature and humidity are held to optimum plus or minus 1%, then by all means solder every rail joiner that isn't at an insulating gap.
My layout space is the diametric opposite of a NASA clean room - dusty, outdoor ambient humidity and annual temperature swing of close to 100 degrees F. And, thanks to a gas water heater, climate control isn't going to happen.
So I let my rail joints slide, lay rail with appropriate gaps (which do open and close with changing temperature) and assure electrical continuity by soldering a jumper around every uninsulated joiner. I learned a long time ago not to depend on rail joiners to conduct track power. The jumpers can flex easily, allowing the rails to expand or contract unimpeded.
As for rail joints at turnouts - I avoid them by using full-length stick rail for stock rails and rails that extend to and beyond the clearance points on the diverging tracks from the frog point. When you hand-lay in place you don't have those six rail joints located just where they're most likely to be troublesome...
Chuck (Modeling Central Japan in September, 1964)
Mr Rrebell,
Every piece of rail - EVERY - is connected to the distribution system by soldered or screw terminal connection, or combination there of. If the rail does not have a direct connection of its own, then it is soldered to a rail that has a direct connection. Rail joiners provide alignment only, no electrical reliability.
In the end you pays your money you takes your chances. What is right for you needs to consider many factors, including environment, skill level and resources.
Finally, if you are using DCC ensure that your work passes the quarter test at all locations, including turnout points and frogs.
Have fun. Dwayne A.
LION solders switches in place. LION even solders several switches together on the bench and brings the whole assembly to the layout.
What if? What if LION wants to remove switch. It happens often enough that the LION knows how to do this.
You cut the rail joiner with a motor tool., turnout lifts right out. It is now easy to flick the remaining rail joiner halves away with the soldering iron.
Repair or replace switch, push new rail joiners on to track all the way past the end of the joiner, drop the switch in place and bring up the joiners to make the connection and solder them in place.
ROAR
The Route of the Broadway Lion The Largest Subway Layout in North Dakota.
Here there be cats. LIONS with CAMERAS
BroadwayLion LION solders switches in place. LION even solders several switches together on the bench and brings the whole assembly to the layout. What if? What if LION wants to remove switch. It happens often enough that the LION knows how to do this. You cut the rail joiner with a motor tool., turnout lifts right out. It is now easy to flick the remaining rail joiner halves away with the soldering iron. Repair or replace switch, push new rail joiners on to track all the way past the end of the joiner, drop the switch in place and bring up the joiners to make the connection and solder them in place. ROAR
I solder all rail joiners including the turnouts. I found out long ago that the one rail joiner that fails to conduct power is the one that didn't get soldered. If I need to replace a turn out I cut the old one out, remove the joiners and replace them with new joiners, install the new turnout and solder it in.
Dr. Frankendiesel aka Scott Running BearSpace Mouse for president!15 year veteran fire fighterCollector of Apple //e'sRunning Bear EnterprisesHistory Channel Club life member.beatus homo qui invenit sapientiam
rrebellJust wonder what the rest of you do and if you feel it was the right decision?
On my previous layout I soldered almost all of the turnout joints. On the more recent layout, I did if it appeared to need it. I guess maybe 20 percent or so are soldered. I approached it individually, and made the decision when I laid the track. Hey, if need be you can always come back and solder.
ENJOY !
Mobilman44
Living in southeast Texas, formerly modeling the "postwar" Santa Fe and Illinois Central
rrebellWhy do you have to replace switches so often?
Mostly because I change my mind on what the layout is supposed to do and how it is supposed to do it. I seldom if ever replace a switch because of derailment issues. Call them "Editors Changes."
Not to mention the fact that most of these switches are on their third or fourth layout, or at least installation on the same layout.
I agree with Texas Zepher and as Mobilman44 says, you can always go back later and solder connections that eventually lose conductivity. Full disclosure: my layout room is environmentally controlled, my benchwork and roadbed is painted to minimize moisture absorption, I use Walthers/Shinohara Code 83 rail joiners which are very snug on their Code 83 flex and turnouts (Atlas joiners are looser) and I treated each rail end with No-Ox before joining. No problems so far after almost 10 months after full operation began.
Dante
For maintenance reasons, I generally leave them unsoldered, but there are a couple of exceptions.
If a turnout is connected to a section of flex track which is curved, I like to solder that joint to keep the sideways pressure from the flex track from forming a kink.
Also, if I've got a complex section of trackwork in an awkward space, I'll solder the whole thing together so that problems don't show up later after a lot of scenery has grown up aroung the track.
It takes an iron man to play with a toy iron horse.
MisterBeasley For maintenance reasons, I generally leave them unsoldered, but there are a couple of exceptions. If a turnout is connected to a section of flex track which is curved, I like to solder that joint to keep the sideways pressure from the flex track from forming a kink. Also, if I've got a complex section of trackwork in an awkward space, I'll solder the whole thing together so that problems don't show up later after a lot of scenery has grown up aroung the track.
Many people bring up the electrical conductivity issue, but fewer seem to consider alignment. Alignment around a turnout, especially coming into the points, is critical for ensuring derailment-free operation. A soldered joint is less likely to be shifted and cause trouble later with equipment being able to traverse it properly. If you feel it necessary to leave a lot of unsoldered joints due to expansion/contraction concerns, it's still worth considering soldering the point ends of turnout stock rails.
Rob Spangler
why do you need a rail joiner if you going to solder the rails together?
if there is no rail joiner, it is not difficult to unsolder rails to separate them for service
greg - Philadelphia & Reading / Reading
Greg,
I have found that the joiners help to hold the joint in good alignment, especially with flex track, coming out of a curve connecting to a turnout; or on a curve, helping to prevent kinks. As mentioned above, it's straightforward to cut through or unsolder a joiner when needed - they are rather thin.
Wilton.
Another vote here for soldering every joiner for electrical reliability. I paint the rails with Floquil paint makers for weathering and by the time you glue your ballast down you could diminish electric connectivity.
Derek
gregc why do you need a rail joiner if you going to solder the rails together? if there is no rail joiner, it is not difficult to unsolder rails to separate them for service
Greg:
A joiner insures a solid soldered joint. Without the joiner you are left with a butt joint that will be of questionable strength.
Joe
gregc why do you need a rail joiner if you going to solder the rails together?
JoeinPA A joiner insures a solid soldered joint. Without the joiner you are left with a butt joint that will be of questionable strength. Joe
Absolutely, and with the joiner it is a much quicker job. You want to get in and out fast to avoid melting the ties.
Removal is easy if you use a de-soldering tool.
Jim