Login
or
Register
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Home
»
Model Railroader
»
Forums
»
Layouts and layout building
»
Wiring an HO Trolley
Wiring an HO Trolley
2702 views
2 replies
Order Ascending
Order Descending
bpolvo
Member since
February 2002
From: US
7 posts
Wiring an HO Trolley
Posted by
bpolvo
on Thursday, December 22, 2005 9:32 PM
I've started and stopped HO layouts for years. Usually stopping at the wiring part. My son asked for a short line HO trolley layout. We decided on an oval with an 'X' through the middle. Two reverse loops. I gapped it in 7 places for standard DC cab control but I also bought an MRC Command controller for DCC. I was told this would be easier. My questions are many because I can't even figure out how to wire the sections for power let alone hook up reverse loops and DCC. I have Atlas selectors and other old equipment. My first qiestion would be how do I attach all the wires inorder to control power to all the sections I've gapped? I know they all need a toggle switch or an Atlas switch but how do I run the wires to these? If someone is interested in helping me I'd write off line with more detail or here if its easier.
Thanks Bob
Reply
MisterBeasley
Member since
December 2004
From: Bedford, MA, USA
21,369 posts
Posted by
MisterBeasley
on Thursday, December 22, 2005 10:00 PM
Since you haven't wired anything yet, I assume that you will be using the DCC system you've bought. That will, as claimed, simplify things.
I suspect you've over-done it with the gapping. For a short loop with an X like that, I would only gap the ends of the X where it meets the turnout from the oval. I think the two sides of the crossover should already be electrically isolated from each other.
The main oval needs to get power. I would wire that as the primary track, directly from the DCC system. You might want to search around this forum a bit for information about installing a "Track Bus," which is basically a pair of heavy wires which run below your tracks, and then are joined to the track every few feed by a pair of "feeder" wires. This isn't strictly necessary, but it will greatly improve your performance.
Next, the reversing sections need special attention. The standard way to do this in DCC is to install a "reverser" module for each one. Again, it's simple to do this - just run wires from your main track power to the reverser, and then from the reverser to the track of the reversing section.
Done. It really is as easy as that. The reverser module takes care of the polarity changes when it detects the train crossing the gap, and again on the other side of the reverser when the train leaves. After a while, you forget about it, because it's so transparent to the operator.
The drawback of the reversers is the cost. They run 30-40 dollars each. With a single trolley, you can "cheat" and wire both reverse sections to the same reverser module, but as you expand your layout and start running multiple trains simultaneously, you will regret doing that. A low-cost option is to wire each section through a double-pole, double-throw switch. The Atlas Twin is perfect for this, but you'll also need a third DPDT switch for the main loop if you do this. This works, but you will have to remember to throw the switches at the right time. (The reverser module is a DPDT switch with brains, by the way.)
It takes an iron man to play with a toy iron horse.
Reply
fwright
Member since
November 2002
From: Colorado
4,074 posts
Posted by
fwright
on Friday, December 23, 2005 10:45 AM
Are you running off overhead wire? If so, the wiring becomes as simple as 3 rail O; the overhead takes the place of the center rail; reversing sections don't matter. DCC still has the advantage of getting rid of the block controls that are necessary for more than one trolley to operate simultaneously.
If not, wire as MisterBeasely describes.
yours in wiring
Fred
Reply
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Users Online
There are no community member online
Search the Community
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT
Model Railroader Newsletter
See all
Sign up for our FREE e-newsletter
and get model railroad news in your inbox!
Sign up