Hi Mark,
The operating session looks like it was a lot of fun. Well done.
Dave
I'm just a dude with a bad back having a lot of fun with model trains, and finally building a layout!
Mark,
Your monthly and annual updates were absolutely fantastic. Your ability to plan and carry out your layout plans are something we should all aspire to!
Don; Prez, CEO or whatever of the Wishram, Oregon and Western RR
Thanks Dave, tankertoad135!
10 July 2022
Since my last photo update of 14 June (wow! Nearly a month ago!) I've continued working on scenery between Casper and into the south end of Wind River Canyon.
I patched that cut-away spot above the rock face:
And went on to add some more rock castings. These will all be blended together with additional plaster, then stain and paints:
I continued brushing on a layer of hydrocal over the plaster cloth in the canyon, getting to this point on 18 June:
I can't go further right now because the plaster cloth that's still exposed is only one layer. I'll add a second layer when I get more cloth, then continue brushing on the hydrocal.
Wyoming has a lot of sagebrush, so it was about time I started to figure out how to make it. Going on a suggestion from someone on another forum, I bought a small block of florist foam ($1.99 at Hobby Lobby) and ground it up in a blender (orange juice is going to taste funny for awhile!):
I cut a tiny length of sisal twine, glued the threads together at the base, and dipped it into a Hunterline weathering solution to make the branches of the sagebrush:
Then I sprayed it with Super 77 adhesive and dipped it in the bag of ground up florist foam. The leaves were a bit glittery, so I sprayed the bush with Dullcote and propped it up on the layout to see how it looked. Pardon the slightly blurry look in the photo - the camera focused on the blue tape behind the sagebrush:
Not terrible I think, but there's room for improvement. It should look more like the sagebrush in the foreground here:
But hey, it's a start.
To get a sense of how much I need, here's a zoomed-out shot of the Powder River / Wind River Canyon section of the layout. The red circle is where that sagebrush is:
Boy, I need a whole more of this stuff!!!
The last week I've been focusing on coating the area between Casper and Shobon, including the Powder River siding area, with plaster in preparation for ground cover (and sagebrush):
The areas nearest the roundhouse are still wet. The color from one batch to the next doesn't match exactly, but this will all be covered with tile grout dirt, spotty prairie grass and other scattered foliage, plus lots (and lots and LOTS) of sagebrush, so the differences in the plaster colors shouldn't be noticeable.
Mark P.
Website: http://www.thecbandqinwyoming.comVideos: https://www.youtube.com/user/mabrunton
Great update, Mark. I'm enjoying dropping in here from time to time and watching everything take shape.
Pruitt Boy, I need a whole more of this stuff!!!
I model southern CO, where sagebrush also abounds. I've tried a bunch of sagebrush techniques, and like the sisal rope (it's great for huge WY brush, I think I first saw it as an O scale technique.) The approach that has fit my needs best so far for smaller brush came from Rob Spangler-- as I remember it, he used 3M grey scrubbing pads that were cut up, pulled and teased apart to make the branch structure, then Super 77 and a sprinkle of the right sage-color ground foam. That might be a good way to make a lot of brush quickly, so you can get that vast expanse covered!
Phil
Thanks Phil!
I checked out Rob's approach to sagebrush. I'm going to give it a try.
19 July 2022
I just posted a video on how I added wifi to my layout:
PruittI just posted a video on how I added wifi to my layout:
That was a very interesting and well done video. Thank you.
I do have one small question. Why are the left and right marker lights on the caboose controlled separately? I have always assumed that both lights would show the same indication. Am I wrong?
Thanks,
Mark, thank you for convincing me to never add Wi-Fi on my iPhone to run my trains.
I should mention that I am a graduate of the Sheldon School of Model Railroading.
Rich
Alton Junction
hon30critterHi Mark, That was a very interesting and well done video. Thank you. I do have one small question. Why are the left and right marker lights on the caboose controlled separately? I have always assumed that both lights would show the same indication. Am I wrong? Thanks, Dave
Both markers do show the same indication. The Light It will only drive one LED per output, so it takes two outputs, which by default are functions 1 and 2. The outputs can be remapped to a different function number, but as far as I know both outputs cannot be mapped to the same function. So each marker is activated by a different function.
richhotrainMark, thank you for convincing me to never add Wi-Fi on my iPhone to run my trains.
Rich, I don't particularly like running trains with my phone either. But for less than the price of one radio throttle (Cab06er), I have the capability to connect four wireless throttles that are more reliable (in terms of reception and transmission) than the radio units. Pretty much everybody who might come over to operate will have a smart phone, so they're all carrying throttles in their pockets, whether they know it or not.
For the future I plan to purchase at least one of the TCS UWT-50's for use at home and at the club.
PruittBoth markers do show the same indication. The Light It will only drive one LED per output, so it takes two outputs, which by default are functions 1 and 2. The outputs can be remapped to a different function number, but as far as I know both outputs cannot be mapped to the same function. So each marker is activated by a different function.
I have to say that I find it a bit disappointing that the Light It can only handle a single LED per output. LEDs do not draw a lot of power so I will suggest politely that they need to up their game (no criticism of your use of the module intended).
In my cabooses I use a circuit designed by Mark R which delivers constant lighting to the marker lights as well as a light inside the conductor's cubicle. The lights are controlled by a magnetic latching reed switch.
Here is the wiring diagram:
The fact that the capacitor is rated lower than the track voltage doesn't matter, but you can use a higher voltage capacitor if you choose. The reed switch is optional. You could use a manual switch. In fact, finding the latching magnetic reed switches may prove to be rather difficult given the age of the technology.
I'm not suggesting that you change your methodology, but my option may prove interesting for some viewers.
Cheers!!
3 August 2022
I just uploaded my latest layout update video:
"One difference between pessimists and optimists is that while pessimists are more often right, optimists have far more fun."
Another interesting video! The pallet company looks good! I don't envy your having to make so much sage brush, but you have a great work ethic so I'm sure it won't take you long.
Thanks Bear, Dave! I was afraid the roof looked too garish. "Subtle" never crossed my mind.
7 August 2022
The past few days I've spent ripping two sheets of 3/4" plywood down to 3" wide strips (in a stiflingly hot garage!). and building most of the benchwork for the Worland / Greybull peninsula.
There's one small section left to add in the foreground, plus a couple more legs. Tomorrow, maybe.
I also have spent a couple hours adding static grass in a small area just west of Casper. This is only the first layer. Yet to coe are low bushes, weeds and sagebrush. Hopefully it get more realistic as I go.
16 August 2022
The last nine days have seen some progress on the layout, notably on the Worland / Greybull peninsula.
On the 8th I finished the benchwork by adding the last section (nearest the camera). Now it's ready for some subroadbed and track!
On the 14th I carved subroadbed out of a couple of sheets of 1/2" plywood and began test fitting them flat on the benchwork.
I was going to begin building the subroadbed for Worland, but common sense prevailed (unusual in my train room!) and I began working on the Cody branch first, which will be located underneath Worland and Greybull.
On the 15th I connected all the subroadbed pieces together and began raising the line to the proper elevations. In the following photo, in the far distance (the curve to the right to nowhere), the line dives under Greybull and Worland (coming towards the camera) with just under 4" of clearance. It descends on a 2 1/4% grade all around the peninsula.
Today I finished the subroadbed underneath Worland and through the tunback curve.
My track plan has Powell (the first town on the Cody branch out of Frannie) on a deck below Powder River, but depending on how the clearances look I may move it to under Greybull instead. I think the clearance to Greybull will be too low to work well, but we'll see how it looks once I have the Worland to Greybull turnback curve in place.
After the benchwork was finished but before I started the subroadbed I paused for a few days to build this tank car kit from Intermountain Railway. This was a series of special kits manufactured for the NMRA's Rocky Mountain Regoin back in 2002. I "inherited" five of the kits from someone who decided they weren't going to use them. This is the first one, all weathered and ready to go. Looks like that baby has a few miles on it!
3 September 2022
I posted this month's layout update:
Your videos continue to hold my interest. I look forward to them every month!
Finally a decent looking shirt, but I would expect no less from the Casper Division Public Relations Manager.
With all due respect to a few other forum members with outstanding layouts, yours surpasses all the others in my personal view. The construction of the layout, its sheer size, and the video updates all combine to capture my interest like no other.
If the forum were presenting awards for Outstanding Layout, yours would get my vote. I hope that you never actually finish the layout because I would miss your video updates. I bet your buddy Dave is shaking in his boots as your layout progresses.
Another outstanding video Mr. Pruitt!! You continue to astound me with your dedicated approach to layout construction and ensuring quality in your work. Your videos are a definite motivation for others of us regarding how to plan and build a model railroad!!
Thanks Dave, Rich (partially) and Don!
Bear, I'll be reporting your family to the EPA, so they can keep an eye on any US relatives.
Rich, don't get used to it - next month I'll be back to the same old grungy clothes I usually wear. Thanks for the very kind words otherwise ! After the comments from you and Don, my ego is threatening to explode like an overinflated balloon!
pt714 I model southern CO, where sagebrush also abounds. I've tried a bunch of sagebrush techniques, and like the sisal rope (it's great for huge WY brush, I think I first saw it as an O scale technique.) The approach that has fit my needs best so far for smaller brush came from Rob Spangler-- as I remember it, he used 3M grey scrubbing pads that were cut up, pulled and teased apart to make the branch structure, then Super 77 and a sprinkle of the right sage-color ground foam. That might be a good way to make a lot of brush quickly, so you can get that vast expanse covered! Phil
Same here except western CO into eastern Utah:
Rio Grande. The Action Road - Focus 1977-1983
3 October 2022
I just posted my latest layout update video:
More great progress despite the stomach issues. Sorry about that.
I think I might be patron #1.
hon30critterI think I might be patron #1. Cheers!! Dave
Fortunately, you're not "the one and only."
10 October 2022
In September I spent just a few hours working on the prairie between Casper and Powder River. Here's what things looked like in early September:
By 14 September I added a few more inches of grass. Powder River is off frame to the right.
By the end of September I'd added more layers of scenery. That new area of grass is closest to the camera in this shot:
But I spent most of the past month working on Worland. About the middle of the month I had cork sheeting over the entire area:
By the 24th I had the trackage through the center of town laid, wired and fully tested. Still to come is the Holly Sugar complex in the far distance (in the dark corner), and Crown Cork & Seal off the turnout on the right near the camera.
Crown Cork & Seal will have the tightest curves on the layout - about 18 inch radius. This is in keeping with the real spur to the facility:
According to my retired BNSF engineer friend, when switching Crown Cork & Seal they could manage to get one Geep through the curves to the facility, but the SD's were too large and could not take the curves.
In early October I built the bench top for Holly Sugar. Support brackets:
And completed platform:
I'm using foam for this area because the beet flume is partially below ground level. It's a lot easier to carve a trench into foam than into plywood!
After the Holly Sugar benchwork was finished, I thought I'd better start building my beet hopper fleet. I began by completing a set of six hoppers. Here's one of them:
And today I started constructing the turnouts I'll need for the sugar plant trackage.
30 October 2022
Over the last couple weeks I've finished Worland trackage, including the Holly Sugar complex, except for Crown Cork & Seal. Here's the mess I made while installing the Holly Sugar siding and leads.
Here's Holly Sugar trackage completed. Only the spur on the left is glued down at this point - the two beet delivery tracks at the right will be elevated over the beet pits by about 12 scale feet, and the molasses loading, coal and lime delivery track, the 2nd from the left, will be open below the tracks where the coal dump is.
Here I am checking the reach for uncoupling cars. The beet tracks will take cuts of cars, with no uncoupling required between cars, so I'll be able to set the couplers to delay mode back at the switch (where the soldering iron is) and push the cars up the low trestles. I'll have to do the same thing with the coal deliveries, since the main plant will be between that track and the aisleway.
I also added feature names to the fascia in some spots, plus mounted throttle pockets and cup holders. Here we're looking towards the yard ladder in Casper.
On 25 October, last Tuesday, I held my first full-up operating session. I took the time to stage three trains (one is a passenger train - a Doodlbug with trailer) in Casper yard the night before, so that the session would start out quickly.
And Tuesday afternoon the layout came to life! From front to back we have Larry, who took on the chore of switching the Casper industries, Phil, who served as Casper yardmaster, Frank, who never has attended an operating session before so just watched, and Harry, who was running the CNW local.
There were several others in attendance as well, including my good friend and retired railroad engineer Dave from Basin. He took on the chore of switching Holly Sugar. When we run sessions set in autumn Holly Sugar will be a madhouse, handling trainload after trainload of beets.
Everything looks great! Congratulations on hosting your first formal operating session!!
Pruitt On 25 October, last Tuesday, I held my first full-up operating session. I took the time to stage three trains (one is a passenger train - a Doodlbug with trailer) in Casper yard the night before, so that the session would start out quickly. And Tuesday afternoon the layout came to life! From front to back we have Larry, who took on the chore of switching the Casper industries, Phil, who served as Casper yardmaster, Frank, who never has attended an operating session before so just watched, and Harry, who was running the CNW local. There were several others in attendance as well, including my good friend and retired railroad engineer Dave from Basin. He took on the chore of switching Holly Sugar. When we run sessions set in autumn Holly Sugar will be a madhouse, handling trainload after trainload of beets.
Thanks Dave, Rich!
You know Rich, I didn't know any of these guys three years ago. If you check around the area a bit, you might find some folks who would enjoy operating your layout with you (if you're so inclined). The entire metro area (if you can call it that) of Casper is only about 80,000 people. That's smaller than most of the country. Maybe where you live has enough people within driving distance to make a crewed ops session possible.
3 November 2022
I just posted my latest video update:
Great update, Mark. I'm in awe of your prairie grass. Wish I still lived in Colorado. I'd gladly make the drive to Casper to be part of your operating crew.
Ray