Login
or
Register
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Home
»
Model Railroader
»
Forums
»
Layouts and layout building
»
Painting a loco
Painting a loco
1493 views
5 replies
Order Ascending
Order Descending
Anonymous
Member since
April 2003
305,205 posts
Painting a loco
Posted by
Anonymous
on Thursday, May 6, 2004 2:01 PM
I was given some old tracks and train stuff from someone's old layout (not all kids with trains still like trains when they grow up). I don't want to use the brass rails on my future layout, but they could be well suitable for a christmas train that my mother would like to have.
Anyway, I've tested the stuff and found that I have a working loco that only needs some repairs. The thing is, since it has been used by a kid back then, there are some paint that has been dropped on it and whatnot, and my mother doesn't want to see a red and black CN train as a christmas train, so I thought I might as well repaint it.
My question is: do I need to remove the paint before repainting? If so, how should I do it?
Reply
Edit
AntonioFP45
Member since
December 2003
From: Good ol' USA
9,633 posts
Posted by
AntonioFP45
on Thursday, May 6, 2004 2:23 PM
Hello Neerie, [:)]
For painting: Will you be using an Airbrush, Spray Can, Spray Bottle, or paint brush?
Yes to paint stripping! Fairly easy. Try the alcohol method.
Get a
small, narrow container or pan
. Go to your drugstore and purchase two bottles of
91% Isopropyl alcohol
(Don't get 50% or 75% as they're not strong enough). Make sure that it will be enough to submerge your model. [;)]
After pouring it in the pan, submerge your model in it for about 1 hour. Afterwards, using a toothbrush, scrub the entire surface with it still in the alcohol. Slowly, continue to scrub and turn the model over. The paint should come right off with little effort. [C):-)][tup]
Afterwards examine the shell. If there are tiny bits of color left in nooks and crannies, don't worry about it. Spray primer onto the shell and proceed with your paint job. If the primer comes out a little rough, you can wet-sand it with
600 grit
sandpaper for a smooth finish. You can obtain
3M Wet /Dry paper
at most hardware stores. Make sure it's the
black sandpaper
as this is designed to be used with water.
*Tip: [;)] If painting mulitple colors, don't use the "cheap" masking tape from the Dollar Store. Spend just a "tad" more and get
3M tape
, preferebly the blue or green fine line tape.
Hope this helps! [:)][;)][8)][:I][^][:X][8)][C=:-)][C):-)][4:-)][tup][swg][tup]
"
I like my Pullman Standards & Budds in Stainless Steel flavors, thank you!"
Reply
AntonioFP45
Member since
December 2003
From: Good ol' USA
9,633 posts
Posted by
AntonioFP45
on Thursday, May 6, 2004 2:52 PM
Neerie,
One more tip. Go to the General Discussion page. Look at the Great Results in Model Paint Stripping thread. Should be helpful as there are a lot of good responses featuring results and even different methods!
Peace and God Bless!
"
I like my Pullman Standards & Budds in Stainless Steel flavors, thank you!"
Reply
ndbprr
Member since
September 2002
7,474 posts
Posted by
ndbprr
on Thursday, May 6, 2004 3:13 PM
Back the paint bus up just a minute!!!!!! You may be able to just go to a hobby shop and buy a new shell for your engine. If it is an Athearn you can definitely do that and save yourself a bunch of time for much the same cost as painting. You could also check E Bay as shells are offered there as well as full engines at very good prices. Either of these ideas may be easier than repainting an engine.
Reply
Anonymous
Member since
April 2003
305,205 posts
Posted by
Anonymous
on Thursday, May 6, 2004 10:46 PM
Thanks Antonio, and I will be using airbrush, we're already well equipped as I'm not the only modeler (just the only one into trains) in the house.
And as for buying a new shell.. nahhhh painting it will be more fun! And beside, it's just for a cheap christmas layout and I want to really do a custom job.
Thanks for the tips!!
Reply
Edit
AntonioFP45
Member since
December 2003
From: Good ol' USA
9,633 posts
Posted by
AntonioFP45
on Friday, May 7, 2004 6:56 AM
Neerie,
Very glad to be helpful. Keep us posted with your progress.
BTW: What paint scheme are you going to apply on your locomotive?
"
I like my Pullman Standards & Budds in Stainless Steel flavors, thank you!"
Reply
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Users Online
There are no community member online
Search the Community
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT
Model Railroader Newsletter
See all
Sign up for our FREE e-newsletter
and get model railroad news in your inbox!
Sign up