Login
or
Register
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Home
»
Model Railroader
»
Forums
»
Layouts and layout building
»
What kind of switchs to use with peco turnout motors
What kind of switchs to use with peco turnout motors
1915 views
5 replies
Order Ascending
Order Descending
Anonymous
Member since
April 2003
305,205 posts
What kind of switchs to use with peco turnout motors
Posted by
Anonymous
on Friday, April 23, 2004 9:47 AM
I am using Peco PL10E motors to control my turnouts. I was wondering if anybody knows a good SPST switch to us with these motors. I am using an Atlas generator to power the turnout motors. This unit delivers 3 amps of power at 15 VAC ( peco recommends at least 2 amps). I was thinking ot using a mini SPST from Radioshack ( #275-1547) which is rated to handle 0.% amps at 125 VAC, but I am not sure if these would be able to handle the current.
Any suggestions would be appreciated.
Reply
Edit
cacole
Member since
July 2003
From: Sierra Vista, Arizona
13,757 posts
Posted by
cacole
on Friday, April 23, 2004 9:15 PM
You could use either single-pole double-throw center-off toggle switches, or two single pole push buttons. Since most of these switches are rated for 125VAC, they should easily be able to handle 12 Volts DC at the current level needed to operate a turnout motor.
Reply
BR60103
Member since
January 2001
From: Guelph, Ont.
1,476 posts
Posted by
BR60103
on Friday, April 23, 2004 10:11 PM
I have found that push buttons (especially the cheap, easily available type) have a tendancy to break down and stick, especially in the "on" position. I think some of that may be from overly-enthusiastic soldering.
Peco make a passing-contact switch that resembles (roughly) an interlocking lever. They also make a "stud and probe" system, where you have a small contact on the control panel (the stud) and a wire with a metal point (the probe), and you just touch the probe to the stud.
--David
Reply
CBQ_Guy
Member since
September 2003
From: North Central Illinois
1,458 posts
Posted by
CBQ_Guy
on Thursday, April 29, 2004 2:00 PM
I accidentally just came across this link which should be of interest to those using Peco turnouts. It is PDF format file so you'll need the FREE Adobe Reader to check it out.
http://www.peco-uk.com/grafix/stream3.pdf
Hope this is helpful to some of you.
"Paul [Kossart] - The CB&Q Guy" [In Illinois] ~ Modeling the CB&Q and its fictional 'Illiniwek River-Subdivision-Branch Line' in the 1960's. ~
Reply
nfmisso
Member since
December 2001
From: San Jose, California
3,154 posts
Posted by
nfmisso
on Friday, April 30, 2004 10:26 PM
The switches must momentary contact. AC or capactive discharge is preferred with twin coil machines. If you use DC, you should install shunt diodes on the switches to prevent arcing with the inductive load.
Nigel N&W in HO scale, 1950 - 1955 (..and some a bit newer too) Now in San Jose, California
Reply
Anonymous
Member since
April 2003
305,205 posts
Posted by
Anonymous
on Saturday, May 1, 2004 3:09 AM
I have used Peco switch motors for over 30 years. I use a SPDT with MOMENTARY contact only. The ones from Radio Shack sound fine to me. Peco motors need a lot of power to throw. I use a Capacitor Discharge unit (I have 80 points motors and use about 20 per CDU. By using one of these if you do get a sticky switch you do not burn out a motor as once discharged they can not recharge until the switch is released. I have also used the old electric pencil (see Peco web site) for details however you will get some arcing on hitting the contact and with a higher power it is possible (I have done it) to weld the contacts together.
STEVE WEBSTER
Modelling the Canadian Pacific in Tropical Queensland AUSTRALIA
Reply
Edit
Subscriber & Member Login
Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!
Login
Register
Users Online
There are no community member online
Search the Community
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT
Model Railroader Newsletter
See all
Sign up for our FREE e-newsletter
and get model railroad news in your inbox!
Sign up