Hey guys,
I finally took the 2023 motor apart, and removed the armature from the motor. I then understood the ball bearing arrangement on these motors. It finally dawned on me--both sets of bearings are below the armature. I took the washers and bearings out, cleaned all of the brown gunk off them with naptha, dried them with compressed air, lightly greased them with white lithium grease, and put everything back together.
Earlier today I removed the collector rollers from their shafts, cleaned them with pipe cleaners and DeoxIT, polished the shafts with 1000 grit paper saturated with DeoxIT, and now everything is back together, ready to test.
If anyone has any more maintenance tips, please let me know!
Thanks a lot for your help!
Steve
Servoguy,
I did not get a chance to take the loco apart tonight, I will look at it tomorrow. I have cleaned the armature twice, and sure did not see anything but the top of the armature and the brushes in there. I wonder if someone else had it apart and left the bearings out? I can always pick up the bearings at the next train show.
Thanks for all of your help, I have learned a lot in the last few days about this stuff. In a few days I am going to try to get the horn working!
Now I am curious. If my 2023 has ball thrust bearings, I never knew it. It may be that I never took it apart far enough to find the thrust bearings. In any event, I don't think you need to disassemble the motor to oil the bearings. Put a few drops of motor oil on the thrust bearings, and it should work its way around to where it is needed.
I have never noticed anything on top of the armature. I am going to take the loco apart in the next few minutes. Does the thrust washer recess into the inside of the brush plate?
Here is a page from the service manual to show you the motor and bearings. Looks like there is a retaining ring holding the armature in place.
Larry
The thrust bearings are just washers, and are easy to lose, so be careful. The armature just pulls out of the motor. One thrust bearing (washer) is on the top of the armature, the other on the bottom. I have a 2023, and I could take it apart to help you if necessary.
Does the armature simply pull out of the motor? Are the thrust bearings made of a bronze colored metal, so they will be easy to identify?
Thanks again!
The motor has a lower bearing that also needs oil. It sounds like you missed.it. If you take the brush plate off of the motor, the armature will come out easily. There are also thrust bearings top and bottom inside the motor.
I did not pull the armature out the motor--I did not know how it came out, and did not want to force it.
I cleaned the worm gear when I removed the truck, and I also cleaned and lubed the bronze gear on the inside of the truck.
Please let me know if there is anything else that should be lubed.
Thanks! Steve
Did you pull the armature and lube the worm gear and it's mating spur gear? That should be done if it hasn't been done already.
Hey Servoguy,
I oiled the axles and also applied oil to the opening in the top of the brushplate marked "oil". Please let me know if there is any other areas that need lubrication.
Thanks very much!
While you were at it, did you also oil the axles and other bearings like the motor bearings?
That's probably as good as it gets. The rollers will get warm, when they are getting too hot to touch, that's when you need to look into remedial measures.
I would consider after 20-25 minutes that is normal. All electric motors produce heat when operating. Moving parts create friction and heat. If the motor was overheating, It would start slowing down. I don't have anything like what you are running but my old steam engines get pretty warm after 15-20 minutes.
Cleaning all the old grease and oil was a good thing to do. That old gummy grease causes the causes the motor to work harder. I had a 44 Marine rocket launcher. It was a finicky runner. Ceaning all that old grease and oil out of the motor brought it back to life.
Thanks for all of your help. I sprayed the rollers and pins out with Deoxit. I polished the rollers with a polishing wheel. I cleaned the track and the wheels with naptha. I removed the truck from the motor, degreased the worm gear, also degreased and cleaned the bronze drive gear in the truck. I cleaned and lubed the 3 bronze gears on the side on the truck. I also cleaned the armature and brushes for a second time. I lubricated the worm gear with a slight bit of lithium grease.
After reassembly, the loco set took off on the track with very little power, and ran much better than before. I measured the voltage on the track while they were running at a very good clip, with no cars, and the voltage was 8.60 volts. After 20-25 minutes I stopped them and felt of the rollers, and they were still pretty warm, but not as hot as before. The drive truck was also warm, not as hot as the other night.
Does anyone have any other ideas?
Thanks for all of the help so far!
I use motor oil to lube the pickup rollers and the commutator. There are some that have an opinion that this will not work, but years of experience has shown that it works just fine. I also lube the rollers inside the transformers and lube the whistle control mechanism (Type V, Type Z, ZW, KW).
I have no idea how corrosion could occur inside a pickup roller. It is turning all the time and should polish off any corrosion.
I recommend using motor oil for all lube needs. It is cheap and never dries out or gets gummy. To disassemble the powered truck, you need to remove the screw on the bottom of the truck. Then lube everything that turns and lube all the gears. Most greases, light machine oils, 3 in 1 oil, Lionel Lube, WD-40, etc., will dry out and get hard or get gummy. I have 50 years or more of experience with motor oil, and it never dries out or gets gummy.
There's plenty of appropriate lubricants for model trains. For the worm gear I use white lithium grease, for the other gears I use 10-30 motor oil.
Again, I think I'd first lube everything, and next maybe try the Deoxit-D5 I mentioned on the rollers.
Have you tried measuring the current required by the locomotive as it runs? I use one of these around the train layout to measure current easily. Clamp-On Ammeter
I see that this locomotive has a worm gear drive. Will the armature assembly along with the worm gear shaft simply pull out of the motor housing if the brush plate is removed? I assume that there will be some old grease on the worm gear shaft that should be cleaned off.
Is there a grease specifically made for model trains that I should look for? Also, what should I use as a degreaser?
Thank you!
Here's a link to the 2023 Lionel Service Manual that should give you some insights. I wasn't suggesting disassembling as a first step.
Thank you for your response. Are the trucks fairly simple to disassemble? What type of grease would you lubricate the gears with after they are cleaned? Is lithium grease OK?
Assuming for a moment that you don't have an issue of drawing excessive current, consider other causes.
Another common cause for hot rollers is poor contact between the roller and the axle it rides on. I've seen this on several locomotives. I use Deoxit-D5 to improve the contact, then rotate the roller with a Dremel brush to help clean the connection area. I've had rollers hot enough to start the lubricating oil smoking, usually this will fix them. If that doesn't work, it's probably time for new rollers.
Excessive heat on the rollers is usually caused by excessive current being drawn through the locomotive. Clean the wheels, rollers and track with naptha (lighter fluid). Spray some contact cleaner in the rollers where they spin on the rivet to get out any dirt also. Make sure the top and bottom armature bearings are oiled. You may want to disassemble the trucks, clean out any old grease, and relubricate the gears. After a complete teardown, cleaning and lubrication, the loco should run better, and the rollers should not get hot.
Hi everyone,
I recently picked up a set of Lionel 2023 Alco locomotives that have seen very little use. I cleaned the brushes and armature and lubricated the axles with a light machine oil. They run great, with one exception-the pickup rollers get quite a bit hotter on these 2023s than they do on my 2025 steam set, running about the same speed and duration of time.
Is this normal for these 2023s? I realize that there is a gearing difference in the steam loco and the diesel.
If anyone has an opinion, I would welcome it.
Our community is FREE to join. To participate you must either login or register for an account.
Get the Classic Toy Trains newsletter delivered to your inbox twice a month