Trains.com

Lubrication

2270 views
14 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    October 2004
  • From: S.E. Ohio
  • 5,434 posts
Lubrication
Posted by Blueberryhill RR on Sunday, April 3, 2005 1:05 PM
What's the best type of grease and oil for the lubrication of engines and cars ? And the best way to apply it ?

Chuck
Chuck # 3 I found my thrill on Blueberryhill !!
  • Member since
    January 2003
  • From: Frankfort, Kentucky
  • 1,758 posts
Posted by ben10ben on Sunday, April 3, 2005 1:14 PM
For oil, I like Labelle brand in the needle-oiler bottle. It's expensive(about $5 from most hobby shops), but it's an excellent plastic-compatible oil. I've also found that their needle oiler is smaller than other brands that I've tried, so it's easier to get into tight places.

Labelle also makes an excellent general purpose grease. I like to use a toothpick to apply it, or squirt it directly into gear boxes.

For your postwar trains, 3-in-1 oil on a toothpick or straight pin, and vaseline on a toothpick or old screw driver work fine.
Ben TCA 09-63474
  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Sunday, April 3, 2005 1:21 PM
Labelle is okay but Lubriplate is the best. Bennie is wrong about vaseline.
  • Member since
    October 2004
  • From: S.E. Ohio
  • 5,434 posts
Posted by Blueberryhill RR on Sunday, April 3, 2005 1:29 PM
Thanks. There are not any hobby shops in SE Ohio, or any that I've heard of. But, I've got the idea. I've never used vaseline..... so I can't comment on that.

Chuck
Chuck # 3 I found my thrill on Blueberryhill !!
  • Member since
    February 2005
  • From: Vancouver Island, BC
  • 23,330 posts
Posted by selector on Sunday, April 3, 2005 2:03 PM
Vaseline is a petroleum byproduct and thus will destroy plastics. You may have to phone and order a tube of laBelle's or Woodland Scenics Hob-E-Lube. Bottom line, get what they sell that is plastic compatible. It may cost a bit, but will last a long time because it should be applied seldom, and then only very carefully and sparingly. Otherwise, you get gunked up pivots and bearings. I use a pointy toothpick because oil will adhere to the end while you place it near the point to be lubed, and the wood doesn't absorb too much of it. A pin or other hard surface will not hang on to enough oil.

Wipe off the excess after you have 'run-in' the oil by moving the object back and forth a few times.
  • Member since
    January 2003
  • From: Frankfort, Kentucky
  • 1,758 posts
Posted by ben10ben on Sunday, April 3, 2005 2:13 PM
Just to clarify, I don't use vaseline on anything other than postwar trains with metal gears. Definitely don't use it on anything with nylon or other plastic gears.

I've used Hob-e-lube before, and I didn't care too much for it. It's a good oil, but the bottle was horrible. Mine was extremely unstable(tall and round, rather than short and oblong like Labelle). It leaked when turned on its side, which happed quite easily, and the needlepoint was much, much larger than the one found on Labelle. I found it nearly impossible to get small drops into tight places like I can with Labelle. In my opinion, the dollar or two saved on Hob-E-lube is not worth the trouble.
Ben TCA 09-63474
  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Sunday, April 3, 2005 2:23 PM
I got an old Marx leaflet printed off the internet and they recomend vaseline. The advantage of vaseline is that it won't drip on your track. But all Marx is basically metal construction. I use a train lube from a hobby store. Its worth the extra money just because it comes with a long needle like applicator. Van Hobbies up here in Vancouver sold me a motor bearing lubricant made by Aero-Car Hobby Lubricants Western Springs Il. It seems to work fine. But I'm going to try the vaseline as I always end up having to clean the track after oiling the fleet. I'm running all metal Marx stock so there is no risk. Let you know how it works!

Mark
  • Member since
    March 2004
  • From: Jelloway Creek, OH - Elv. 1100
  • 7,578 posts
Posted by Buckeye Riveter on Sunday, April 3, 2005 5:06 PM
Blueberry, there's a good train store in Lancaster, Ohio that has all of these types of lubricants. Also, there is a store in Huntington, WV.

Some hardware stores also carry special lubricants.

Celebrating 18 years on the CTT Forum. Smile, Wink & Grin

Buckeye Riveter......... OTTS Charter Member, a Roseyville Raider and a member of the CTT Forum since 2004..

Jelloway Creek, OH - ELV 1,100 - Home of the Baltimore, Ohio & Wabash RR

TCA 09-64284

  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Sunday, April 3, 2005 5:42 PM
I too have been using Labelle oil on both Postwar and Modern Lionel and Flyer pieces with no problems. I've also used Labelle 106 Grease on gears during the same period with excellent results. Their grease is compatible with plastic and dosen't seem to sling all over the engine and tracks like some other types of grease do.
  • Member since
    February 2004
  • From: Rolesville, NC
  • 15,416 posts
Posted by ChiefEagles on Monday, April 4, 2005 9:08 AM
Labelle grease. Emptied a needle oiler and refilled it with Slick 50 One Lube [synthetic oil, plastic friendly]. Slick 50 is really slick and works great for oiling.

 God bless TCA 05-58541   Benefactor Member of the NRA,  Member of the American Legion,   Retired Boss Hog of Roseyville Laugh,   KC&D QualifiedCowboy       

              

  • Member since
    February 2005
  • 1,821 posts
Posted by underworld on Monday, April 4, 2005 1:23 PM
Chief Eagles has a good idea with the Slick50. I use the Labelle or some other plastic compatible oil mixed with a little bit of a product called Motor Kote. www.motorkote.com

underworld

[:D][:D][:D][:D][:D]
currently on Tour with Sleeper Cell myspace.com/sleepercellrock Sleeper Cell is @ Checkers in Bowling Green Ohio 12/31/2009 come on out to the party!!! we will be shooting more video for MTVs The Making of a Metal Band
  • Member since
    September 2004
  • From: Middle o' Nowhere, MO
  • 1,108 posts
Posted by palallin on Monday, April 4, 2005 1:48 PM
For pin point oiling, use cheap, disposable syringes. Using our kinds of oils, the rubber stoppers take many months to deteriorate. I've only had to replace mine twice in 5 years.
  • Member since
    July 2003
  • From: Watkinsville, GA
  • 2,214 posts
Posted by Roger Bielen on Monday, April 4, 2005 3:57 PM
For axels and couplers I've been using the teflon/oil used for the cam on compound bows, archery. I use a hypo to apply it.
Roger B.
  • Member since
    October 2004
  • From: S.E. Ohio
  • 5,434 posts
Posted by Blueberryhill RR on Wednesday, April 6, 2005 3:04 PM
Buckeye..... can you give me the name of the hobby store in Lancaster, that you were referring to. I found 4 listed and have not visited any of them. Thanks for the help.
Chuck
Chuck # 3 I found my thrill on Blueberryhill !!
  • Member since
    April 2003
  • 305,205 posts
Posted by Anonymous on Wednesday, April 6, 2005 4:25 PM
QUOTE: Originally posted by selector

Vaseline is a petroleum byproduct and thus will destroy plastics.
I'd like to say "rubbish" to that...so I will:

RUBBISH!!

I've used Veseline on so many plastic gears I can't count 'em! As my dad did before me.

I guess the fact that my Vaseline comes in a plastic container means little.

BTW, I also use real steam oil (also a "petroleum byproduct") on my engines as well.

Join our Community!

Our community is FREE to join. To participate you must either login or register for an account.

Search the Community

FREE EMAIL NEWSLETTER

Get the Classic Toy Trains newsletter delivered to your inbox twice a month